11016202690 Kenmore Washer - Instructions

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Purchased and installed PS1485646 COUPLING, MOTOR (Direct Drive Coupling). We googled "Washing Machine making a grinding noise. Several people suggested coupling probably broken. We located some instructions online regarding dis-assembly, sure enough,the coupling was broken. We ordered the part from Partselect.com. It arrived in three days, replaced the broken coupler. Washing machine back in business for around $20. Hooray! Thanks, Partselect!

Disconnected power, all hoses. Tilted washer backward to see underneath. (Placed sturdy 6" high object under back of washer to keep it from going flat on ground and possibly damaging hose connects). Looked for area where motor and transmission connect. Saw broken part (coupling). After trial and error, figured out how to remove pump and then motor, by removing strap type holding clips, and then broken part was accessible. Ordered part online and was easy to install and reassemble washer now that I knew how it came apart. If I had known the part name or number beforehand, I could have watched the replacement instruction video on this site, but I figured it out anyway, and I did it without removing the whole control switch panel and side panels/body of washer, like they do in the video. But..I guess they had to do that to give you a good view of all the parts and things they were removing underside. I recommend watching video for this part install,so you see what needs to be removed and how underneath, but then just tilting washer back to access underside, without all that control panel and sides removal.

Watched the video and followed the instructions. Everything went smoothly and the repair was done in under 15 minutes, less time than it took to mop up the water when it overflowed telling me that there was a problem.

Sprayed wd40 - limescale - boiling water , NOTHING WORKED after half an hour reapeted spraying and pulling the tub and shaking it back and forth - still nothing
Finally I replaced the center nut loosely than putting a piece of wood on top of it and with me holding the tub slightly high - my wife than whacked it hard several times , I also was turning the tub every whack
When it came out it was full of rust and grime - it would have never come out without what we did
Replacing the the rubber washer was easy - machine works and no more leaking- thank you for your video which really helped to start the job

Clutch was noticibly worn compared to new part. Direct drive flange had broken, this part should be steel. found a you tube video that was simple to follow. no problems

Replaced motor starting capacitor. Noticed water leak at pump and replaced pump

The instructional video that was attached with the part I purchased was spot on with very simple instructions. The inlet valve came with a metal bracket that was not needed for my model, so just tossed it. Was completed with replacement in about 30 minutes with help from my aspiring handywoman wife (would have taken 15 minutes without her)

I watched a youtube video made by the site on how to replace the lid switch assembly. It showed you exactly how to do this repair. Without watching the video, it would probably have stumped me. After watching the video a couple of times, it was really pretty easy to do. The timer on our washer also needed replacing. I followed the instructions by Joe from Covington, GA. That repair was really easy. Thanks, Joe, for the easy to follow, complete instructions.

to change it was 1,2,3
thank you guys

Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. Replace the coupling and reverse the steps.

The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.

Removed the old hoses and screwed on the new hoses.

Remove metal cover; remove pump, remove motor, remove tub spin assembly; remove transmission. Remove clutch be removing retaining ring. Installation was reverse. No problems, part worked like champ.

Note: Called Sears to see if I could get the part locally. Turns our I had to call an 800 number. Lady said that the part was not carried and would have to be shipped from warehouse. Tried to sell me some discharge hoses. Then said the part would cost $65 before S&H. Told her I didn't want to spend that much, she asked how much I wanted to spend and seemed upset when I told her your price. She didn't comp it, just said that theirs was an official part from Sears, blah, blah, blah. Anyway, thanks for the great service!

Disconnect power & water then drain hoses.
We flipped the washer on it's side to gain access to the bottom. There was no need to take off the back panel. Keep a 5 gallon bucket and a few rags handy for the extra water in the pump line.
Disconnected the wiring harness. Removed the brackets holding the motor. It's a little tight on the back bracket. It has a 1/4" hex nut on the back side, so I used a 1/4" drive socket (see: small). Removed the bolts holding the gear case (this makes it a lot easier). Disconnected the pump hose and rotated the motor & gear box and pulled forward. This gives you access to the coupling. Remove the broken part. Clean the area for debris. NOTE: each part of the coupling has 3 fingers (these are what breaks off), so check to make sure you get all broken parts. Insert the new coupling. It has 3 parts; the plastic fittings go on tight and need to be snug to the shaft. Use a screwdriver handle on the center and tap down with a small hammer. Spray silicone on the rubber coupler to allow a little better slide.
Reverse the process. Line the gear box and motor up and push back into the tub assembly. We used 2 people to do this. It's easier to have someone stand over it and hold / rotate the gear box while the other one can align the motor & bolt everything back on.
It took us an hour, however, if you were doing a couple you could get it down to 30 min. flat.
Go wash your clothes!