1100PRW Magic Chef Range - Instructions

I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".

Figured it had to be the ignitor. I didn't use a multi-meter. Since the appliance was so old, if the $50 igniter didn't do the trick, I'd just replace the oven. Install was super easy, and now oven works great!!!

Broiler lighting fine but main oven burner not lighting. I deduced the oven igniter was most likely the point of failure. Decided to replace empirically rather than time and money for service call. Process was about as easy as replace a computer part. Removed pan and flameguard. Unplugged part from below (after removing drawer). Such a simple plug I didn't bother to throw the breaker / power down the oven. Pulling it out to get to wall plug not an option. Unscrewed old part, saw a flaw had developed in the element. Screwed on the new part, plugged it in, inserted insulation in the hole. Tested for lighting - lit first time. Replaced guard and pan, oven has worked reliably since. Research time was 5x the repair time, but in all a fraction of time and money to have a "pro."

well my brother was over,he said he had the same stove with the same symtoms so we removed bottom tray of oven lifting from the back first then the front.there inback is the igniter.pulled wire out carefully and unplugged and unscrewed 2 small bolt's,replaced igniter remembering it is very fragile,plugged igniter in replaced insulation around wire,saved me from a new oven,thank you partsselect.ps part arrived the next day wow

I removed the oven door and floor, removed the two screws holding the old part in place, unplugged it from the wiring harness and plugged in the new part and replaced the screws. Fixed in 5 minutes.

Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!

I am a novice at this, so before I did anything I researched this site and made sure to read the installation directions that came with the part.

First I removed the oven racks, the bottom cover (one screw in front and two back latches by moving them towards me) and the fire cover underneath that. Next I disconnected the electrical plug in the back.
Then I removed the defective part by unscrewing 2 back panel screws and 1 on the side of the igniter itself. Now, in connecting the new igniter I cut the connector off of the old one and wire nut connected it to the new one. I did check the connectors and cleaned them by simply plugging/ unplugging them a few times.
Next, The trickiest thing about installing the new igniter was pushing the wires all the way to the back of the oven. I took care and time in this to insure that the connection was well insulated from the heat and then plugged the hole with the insulation material supplied. Next I recconected the fire cover and turned it on. Worked great! Put everything back together, plugged it in and Voila! Like new.

I unpluged the oven, removed the oven door by slideing it off the hinges, removed the racks, took the bottom pan out exposing the igniter,while attempting to remove the 2 screws holding the igniter to the bracket, I discovered that they where stripped so I had to use vise grips to remove them. I went to the hardware store bought replacements and installed the igniter. I then removed the protective cover over the wires, stripped them put on the wire nuts provided with the kit put the protective shield back pluged the unit in turned it on, checked it, then put it back together. The stripped screws were the only difficult part.

I unpluged the electrical cord first. Then pulled the stove away from wall. Next removed oven racks, the bottom of the oven. Then removed the deflector plate over the burner. The next step I removed the broil pan. Now the oven area is empty. Nice and easy to remove the igniter with nut driver. Two screws and wire nut that are behind the stove wall. Now I just reversed the procedure. Very easy. The only thing I'm not sure where the insulation block go's. The wires go through back oven wall hole. There was no insulation there before? So I put a small piece just behind the igniter over the wire. Will this catch fire I don't know? If someone knows let me know. Other than that it works.

I removed the two screws that hold the element. This took most of the time because one of the screw broke. Then I unplug the power,took the igniter out and disconnect the wire and reverse the procedure.

installed new control unit had to use the old dial so it would match . Toughest part is the cleaning! needed it.

put it on, perfect

I first looked online at a video on how to replace the igniter prior to recieving the part. The part arrived 2 days after I ordered it (Christmas Day) and was an exact replacement. Taking the oven apart was the most difficult issue since there was some grease missed in the last cleaning plus a couple very tight screws. The igniter unplugged easily and reinstalled without cutting/splicing any wires. Oven was back together and fired up within 20 minutes. Outstanding service and would highly recommend PartSelect.

uninstalled old igniter like video showed and reinstalled new one and then tested right away thank you for your help