108R General Electric Range - Instructions

Dave from West Hartford, CT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Drip pans were disgusting.

Just an easy replacement. Problem was, I couldn't find the parts. The service and turn-around was fabulous!

Parts Used:

Gerri from nashville, TN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Condo Had Very Old Drop In. Threw Away Drip Pans And Rings

Placed new ones on range. Exactly what I would do to wash them.

Parts Used:

Valerie from Ogden, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Threw away old parts!

Put bowl in and then slid rings around. Just like cleaning procedure. Easy. Thanks for your service.

Parts Used:

Valerie from Ogden, UT
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

The burner only heated half of the coils

The repair went well and once again my stove that was installed back in 1968 is working perfectly. We will be buying another 6" burner and 2-8" so we have them when they begin to burn out. We looked everywhere for a replacement and was told they do not make them anymore, but we found it here. Thank you!

Parts Used:

Tilt Lock Hinge Mounted Surface Unit - 6"

Patricia from Tamaqua, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers, Wrench set

Was this instruction helpful to you?

dirty drip pans and rim trims

Threw away the old ones after lifting burner rings. Put new parts in place.

Parts Used:

Anna from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

old stained drip bowls

I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners up, and slide them in. No problem.

Parts Used:

Peter J from Oceanside, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

heating element burned out.

Replaced 30 year old stovetop cooking element with no problems. Stovetop works great now.

Parts Used:

Tilt Lock Hinge Mounted Surface Burner Kit - 6"

Joseph from Bremond, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

(2) Burned out heating elements - 1957 Blt-In Rge top

Turned off elec. at switch box. Took new element out of the package placed it upside down to the side of the old element. Removed skrew holding old one in place, removed old element and turned upside down,removed wires from the old one and put them in same postion on the new one. Repeated for the second unit, all very simple, only needed a skrew driver and less than 30 minutes for both. Wife thinks I am superman - thanks.

Parts Used:

Tilt-Lock Hinge-Mounted Surface Burner - 8"

Tilt Lock Hinge Mounted Surface Burner Kit - 6"

Sam from Silver City, NM
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

one element suffered a small puncture where the heated element burned thru

The old burner was disconnected by unscrewing the wire connectors. The new burner was installed by reconnecting the same wire connectors although the white and red connectors had to be swapped to make the inner element go on when #2 or med switch is chosen.

Parts Used:

Tilt-Lock Hinge-Mounted Surface Burner - 8"

Frank from Beckley, WV
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Socket set

Was this instruction helpful to you?

worn out gasket

Used a putty knife and dental pick to remove old gasket remnants and installed new gasket with putty knife and thumb pressure

Parts Used:

Silicone Door Gasket

Jon from Bishop, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins

Was this instruction helpful to you?

Original trim ring did not fit

I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.

Parts Used:

Sarah from San Andreas, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

dirty drip pans and rings in new house i bought

could not find the proper pans and rings in any diy stores, as stove is so old. went on this site and there they were!!!

Parts Used:

patricia from richland, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

I needed new Drip Pans

I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!

Parts Used:

Gloria from San Jose, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

dirty drip pans

My stove top is 35 yr old. & Lowes did not have drip pans that fit. these worked great & easier than cleaning the old ones. They just popped right in.

Parts Used: