108R General Electric Range - Instructions

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

Replaced all the ordered parts, and straightened a bent "rest piece" (one of three) on the element os the large burner, which made it rest perfectly on the new Trim Ring. It doesn't easily fall down into the bowl now while I am using the burner. The new Bowls look so nice, and the stove looks nearly new!

I now know where to go for help when I need to repair appliances. You seem to have everything that could possibly be needed. Thank you!

The oven is 70 years old and used several times a week so getting it to come apart wasn't working.
Used a light oil and some thinner to work loose the old seal, which was stuck pretty good, removed it by lightly prying the seal lip wider and pulling it out, mostly piece by piece. The worked in the new one and became of the light oil, it went in rather easy. Had to trim an inch or so from each end and wiped down and cleaned up. No more problems....

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)

Replace part an wires

I just replaced them.

Lifted burner element to remove pressure on ring and drip bowl. Removed old parts and replaced in reverse order. This not intended to sound sexist, but my wife who is not particularily mechanically inclined performed the task on her own.

Finding a replacement element for a 30 year old GE electric stove was difficult to find. I was overjoyed when I found a replacement on Partselect! It was a simple "Unscrew, reattach wires and install" all in about 10 - 15 minutes all with a nutdriver. Plug in elements are common but to find one with screw connections is not easy, THANK YOU PARTSELECT! A $48.00 investment (Element with trim ring) was worth the cost compared to a $1,400.00 replacement. You just made a loyal customer, again, Thank You.

Lenny
Nazareth, PA

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

the replacement items fit really good. It was a matter of remove and replace,

Just lifted the electric components Remove drip plans and trim rings and replaced with new drip pans and trim. Your company was incredible in there delivery of the parts..One day. You made my husbands very happy.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the four wires The element i request was 3 elements and i received two element but it was very easy i connect only the 3 wires.