107RC690H Hotpoint Range - Instructions

This is twin oven range with controls at side of upper oven. Control panel was fastened with screws at top and bottom. Range has built-in hood at top which had to be disassembled to reach top screw. Once had access to top screw, eaisly removed control panel and replaced control. New control had identical connections as old control so only had to install it, break shaft to correct length, and use proper shaft adapter for knob. Remounted control panel and range worked perfectly. This would have been a very quick job except for having to deal with the built-in range hood.

TURN POWER TO OVEN OFF AT POWER PANEL 1- Remove element: 2 screws ... cut wire at element because of burned area. 2- Crimp two new wire lug connectors onto wire and attach to new element with supplied screws. 3- Attach element to back of oven: 2 screws ... TURN POWER ON AGAIN AND TEST OVEN

Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!

As easy as 1-2-3 !!! :) Lift up burners, place drip bowls down then trim rings, put burners down! Could not be faster or easier! :) I Could NOT find these parts ANYWHERE !!! :) After much aggravation, I was EXTREMELY happy to come across these parts at PartSelect, online! :) Thanks so much for the diagram, you made is sooooooo EASY to find the precise parts that I needed, now I can cook !!! :)

Couldn't find drip pans locally that fit my stove. I came here by chance searching the internet and found the parts I needed and had them in my hands within a day or two!! Not a big parts repair story but excellent service and shipping!! Will buy from again when needed!

My stove top is 35 yr old. & Lowes did not have drip pans that fit. these worked great & easier than cleaning the old ones. They just popped right in.

My husband was able to easily remove and replace the switch and know with-in 15 minutes.

(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.

Simply removed old and inserted new. No tools necessary.

slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.

I stripped one wire on the first burner. Then I realized that the terminals were the ones that could be left. Finding a replacement terminal has proved to be difficult. Once I realized my mistake I could change the other three burners very easily.

I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.

I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.

Replaced old bake element by removing two screws holding it to back of oven. Disconnected old bake element from lead wires by removing two other screws. Installed new bake element by reversing the process. Only issue is that the tabs on the element that connect to the leads are easily bent and you need to use vise-grips to keep from bending them. Otherwise, very easy. Thank you PartSelect.com for stocking this item that I used to repair my 45-year old GE range!

could not find the proper pans and rings in any diy stores, as stove is so old. went on this site and there they were!!!