10689583706 Kenmore Ice Maker - Instructions

Unplugged the unit. Removed 2 screws to remove front cover to access the cutter grid.removed 2 screws to the cutter grid, unsnapped power connector and removed broken grid. Slid new grid in place, reconnected power connector, replaced screws, plugged in ice maker and slid back in place. Very easy!!!

I replaced the two pumps, since both were the same design...figuring if one went bad then the other would soon go bad...and then I also replace the water level sensor. All had quick connect plugs. The time is just taking apart the various pieces, cleaning, installing the new pumps and sensor, then reassembling.

Figured out You have to pop off the cocer than remove the 1/4 hex head screws only not the philips ones

Having read a few of the user reports like this one gave me the confidence to do this repair. The space was really tight, but one of the write ups suggested removing the frame and then replacing the motor on the frame. That was an excellent suggestion. The only difficulty I had was when I used the motor screws from the old motor to install the new motor. They were slightly longer and didn't tighten down all the way. So the first "test" resulted in still having a noisy fan motor because it was shaking around a bit. But, taking it back out and using the screws that came with the new motor did the trick. The refrigerator is now whisper quiet all the time. I also appreciated the conversion wiring harness in the kit that was simply plug and play for this new motor to my old refrigerator.

Remove back panel on unit locate condenser fan and motor remove three small screws holding motor assembly to metal bracket disconnect electrical connection press new fan blade on new motor reverse directions

Disconnected power cord, removed rear cover of refrigerator, disconnected pig tail, removed 4 housing screws, took three mount screws out and removed old fan. Reversed steps, plugged in and complete repair done.

I determined it was the cutter grid because there was a broken wire on the existing one. They have to heat up and cut the ice. I ordered it and the part was at my house in 1 day. The cutter grid part was easy to install. The ice maker is working great now.

Had repair man out to make repair his price for part $219.00 and $271.00 labor as he was looking up his price I got on line and found part here for $121.00 thought it might take me 1 hour to fix only 6- 1/4" nuts 2 screws and less than 30 min I had Ice maker working. Bottom line my total cost $75.00 repar man $121.00 part $196.00 that was a savings of $294.00

Remove ice tray and guard over moter. Un plug the 3 plugs and pull the entire motor assembly out. Use a screw driver to gently pry motor out. Snap in the new motor(the wiring was on the wrong side and the power cord coloring backwards on the replacement motor, but I snapped it in with the colors criss crossed and it worked). Re plug in the 3 plugs. Re mount mounting assembly, tray and then guard. Had a little trouble getting the tray back in. There is a little flap in the back that goes inside the tray. Other than that, a pretty easy fix.

Repair was so simple, I didn't even need instructions. Removed old fan with motor, installed new one, installed harness that converted plugs, done. Saved hundreds of dollars doing the repair myself.

Unplug regrigerator power cordfrom wall outlet. Using nut driver remove cover from lower back side of refrigerator. Unplug wire connection to fan. Using nut driver remove the four screws holding the fan/bracket assembly. Carefully remove fan/bracket assembly from refrigerator. Using nut driver,remove the old fan from fan bracket. Using nut driver install new fan on fan bracket. Carfefully install new fan/bracket assembly and install the four screws. Plug wire connection to fan (you may need to use adapter supplied with new fan). Reinstall refrigerator lower back cover. Plug refrigerator power cord back into outlet. Note: you may wish to carefully vacuum dust from back of refrigerator before installing back cover. You should also vacuum dust from front side.

UPS delivered the part at 11:05 AM and I had it installed in less than 30 minutes. No issues, easy removal and re-installation although the compartment was very tight for my hand and a 1/4" drive socket wrench. One installation suggestion however, pre-thread the 3 mounting screw holes on the motor housing first by screwing one of the screws provided into each of the three mounting holes on the motor housing prior to attempting to install the new motor. This way you'll find it much easier to get start the screws given the very limited work-space behind the fan compartment.

I called the 800 number and the lady was great to work with and helped me thru all the order process and confirmed the numbers. She also told me she would try to get the order out that day which she did and I had the part two days later. When it arrived I went to the web site and reviewed the video and went to work and all went as the video said. Thanks for the help and if i need another part I will visit your site or call.

I watched the film on installing and taking out. Step by step. easy.

Removed lower plate on back of refridgerator and changed out fan. The video was great and made the repair a snap. Fan is quiet and no more overheating refridgerator.