1068609541 Kenmore Refrigerator - Instructions

The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.

I tipped the refrigerator back and my friend used an adjustable wrench to attach put the new wheel assembies on. I also used a socket wrench to get the old attacheement bolts to thread. I rolled the cleaned appliance in place and adjusted the wheels with the socket set for easy door closing. It went smoothly.

For a year the filler tube would freeze up and stop all water flow. I would remove it and use a heat gun on it. I decided that the fill valve was leaking after 20y and actually saw drops coming out of the tube when the valve was off. So I watched the videos and ordered the parts. So far no freezing up and working as originally. The valve kit came with all the parts I needed to replace and reconnect the plastic and copper tubing connections. Very pleased with the outcome after a week as well as the videos and complests parts needed. The fill tube didn’t need shorthing and was used as it came. Adding, easy to replace and connect to the water supply line. My refrigerator location made the repair a little difficult ( small kitchen) but with patience it all went well. Not as difficult if access to the back side is easier. Not the fault of the parts supplied! Also to mention, I vacuumed out 20 years of dust from the coils while I had the back off. Same for the front side. A must do often to extend the life and air circulation.

Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!

Ordered new fan motor on line took out old motor and replaced with new one

I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.

removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.

Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Replaced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)

Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

I followed the simple steps outlines in the great video! Thanks

Unscrew broken piece, pull it out and then insert new one, security it in place and connect water line again, make sure It's thight check for leaks and done

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.