1068480080 Kenmore Refrigerator - Instructions

Remove freezer shelves, panel, and change fan.

I followed the instructions that came with the part. Less than five minutes it was good as new.

The shelf support the refrigerator crisper container end had broken off. I found the part on the website and viewed the installation video. If I had not seen the video I would have had difficulty completing the job. Following the video instruction the old bracket that supports the shelft broke off. But, because I had been covered in the video how to remove the bracket enabled me to overcome the part breaking. Good set of instructions made the job go well even with the bracket breaking.

changed bulb

Removed correct part from those provided and slipped it into position. No tools necessary.

I simply watched the repair video and did it! Super easy, needed start device and capacitor. As easy as unplugging the old and adding the new. The video helped and gave me confidence. Wives can fix fridges too! Saved me $2500. Looks like I'll need a new excuse if I want a new fridge.

This repair was super easy. there are only 5 screws to remove to get at the defective switch. 3 in the housing where the light bulbs are and 2 in the front trim piece where the cooling adjustment dials are. I never did unplug the fridge ,but probably should have although nothing bad happened. I removed all 5 screws using a 1/4" socket ( a nutdriver would work well also). there is also a small dia rod that comes down from the coolness adj. wheel that when you re-assemble goes though the middle of the wheel. The switch has only 2 wires that clip on with the push on flat type connectors. Very simple. I removed the wires and then the switch can be removed( it is only held in by 2 squeezable side clips). I put the new switch in and connected the wires , checked to see that the lights went on and off. which they did. then just put the screws back in.....done. also I would like to say that when I ordered my switch it came super fast. I ordered it online at 11:00am on a tuesday and it was on my doorstep in wisconsin by 10:00 am the next day...Thanks

I looked for the obvious sign of malfunction, a leak lack of air flow dirty coil finding nothing obvious I checked the electrical components and the first was the start relay with a bimetal temperature switch was the problem that was identifyed when removed due to the relay sounding like it was internally damaged because of severe rateling

I was careful to unplug each cord one at a time so that I can easily match them up to the new start relay. Once I got the cords plugged into the new start relay, I went ahead and plugged in the fridge and it worked like it never stopped working. I must admit, I'm still nervous about this fridge because I never had to do anything like this in my life so in the back of my mind, I'm always wondering if I did it correctly or not. I was giving a lesson on how to make sure that I have it on correctly but that didn't put me at ease..lol. Parts Select sent this part in less then a day and that made me appreciate there business even more. I was concerned that the part wouldn't get here until later on that week.

Replaced bracket-amazed to find how quickly I was able to id the part on this 20 year old refrigerator. Ordered the part and received it the next day! Thanks for the good service! , Bob

I hesitated to fix this for months, thinking it would be difficult so we just put up with a wobbly shelf (food articles would slide off occasionally) then I discovered your help videos and gained the confidence to perform the repair after watching the "how to". Now our food items are secure inside the fridge! Thanks for a great repair source!

I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.

Unplugged Refer...Cleared top shelf...removed screws/covers to expose thermostate and capilary tube...removed old thermostate takeing care to notice how Capilary tube was routed and electrical connection were made (wire color coding)...removed sheath on old capilary tube and installed on new, always making sure to not "kink" tubing...installed new part just as the old one was...plugged refer back in and enjoyed trouble free operation.

Watched the video link from the part order and the step by step instructions were as easy as the repair man showed. This is an easy do it yourself job that will fix the problem I describe with the unit. Ahhh a working freezer making and keeping ice once again.

Thermostat replacement