1068265512 Kenmore Freezer - Instructions

Replaced broken shelf bracket

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

Follow instructions from owners manual. top hinge first then move door upward and replace broken cam with new parts

Just as shown on a you tube video showing the steps involved, except I did not need to drill and tap the hole in the door. Cam repair kit contained all the correct parts.Freezer door is still working fine so I did not need to repair that door.

I was quoted $212.00 by a service co. to make this repair. When I investigated online @ Part Select, they had all of the parts shown on schematics of each section of the refrigerator/freezer (side by side)with part numbers shown. It was easy to find the necessary parts.The cam kit came as a package for both doors and cost $12.00 plus shipping. Installation instructions were included.It took me an kour to make the repair. The hardest part was removing all the condiments from the shelves and remembering from which shelf they had to be returned. Net savings $200.00

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.

I'v used you 2 times for repairing my fridge and clothes dryer. . . . . So far you've saved me over a grand by doing it myself. . . Plus your service is nothing less than astounding. . . . . Both times I ordered early in the day and I got both orders the next day. . . . . You guys are sure on the ball. . . . . . Thanks

I followed the video instructions available on the net. Hardest part of the job was getting up off the floor after I disconnected the water line. I'm 90 years old

Part arrived overnight. The How-To video at PartSelect showed the procedure exactly. It took about 30 minutes.

Removed the door, installed the lower cam & re-installed the door. Diagram & parts list correct. An easy repair.

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

1. Used fine tip marker pen to draw outline of upper hinge position

2. unloaded food from door

3. took decorative cover off upper hing mount

4. loosened 3 screws (not completely) and lifted up upper hinge to permit upper door pin/hinge to come free.

5. lifted door off lower hinge.

6. remove broken pieces, cleaned, put in new pieces, added small amount of grease

7. put door on bottom hinge.

8. put top hinge into door

9. snugged up three screws in top hinge plate.

10. had to loosen top hinge screws and tap hinge plate around to get door to close by itself when about 1-2 inches from being closed

Best part was PartSelect save me bunches of money and got parts quickly