10679472411 Kenmore Refrigerator - Instructions

We followed the video on the KitchenAid website. We turned off water valve at the wall, unplugged the refrigerator, removed the old icemaker by unscrewing the three mounting screws. We unplugged old icemaker from electrical source at back of refrigerator freezer compartment and removed it. We detached the on/off bar from the old icemaker and installed it on the new icemaker. The new icemaker fit perfectly. We plugged in the electric wire to the existing power cord at the back of the refrigerator freezer compartment. We placed the new icemaker in the same position as the old, making sure the mounting screw holes were aligned. Plugged refrigerator back in and turned on the water. Works beautifully.

It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reattached the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.

removed the three screws holding the old ice maker in place - unpluged the electronics .... took the new ice maker pluged in the electronics screwed in into place and we were in business and had ice within an hour.

The repair was very easy. I ordered the part from Part Seelect and the delivery was very quick.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one screw and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.

So easy to do a cave man could do it.

At first ordered the wrong part. Using the website was difficult to find the correct part, but once I called, it was pretty easy to find the part needed. Part showed up and install was only a few minutes. No more leaking!

Thanks for the help PartSelect!

That 1 Phillips screw out push up disconnect electrical plug put new one in by going in the opposite way.

3 screws and plugged in the new ice maker. It was slightly difficult to unplug the old ice maker and place the plug in the new ice maker. Still really easy. New ice maker works great!

i can't believe it was that easy, just removed the screws, pulled elements out disconnected wires well it seemed to easy so had to read the directions or it would have took only 10 minutes. to do this job. thanks so much for your web sight, the repair man said it would probably be 200.00 or so

yea right 100.00 and its making all the ice we need thanks

joan mcquain

It was very fast and easy. Two screws to take of the ice door cover. the ice maker itself just slid out and all I did was disconnnect the wiring harness. Unscrewed the plastic bottom case and screwed onto the new one. Attached the harness and slid it back in.

it was very very simple, it took only three screws
using socket set.
I removed the old one and put the new one in place , connect electric connection in 2 seconds snapping it toghether, that is all to it.
the hardest part is waiting on the ice to be made , which it took three to four hours for the first batch.
I am in the medical profession, IF I CAN do it , everyone CAN!!!!!!!!

First I unpluged the refriderator and removed the old ice maker. I then just simply installed the new ice maker. It was just that simple. The next morning I woke up with a full tray of ice.

Removed one screw on cover covering wires on old ice maker,disconnected plug, removed ice maker, checked connector to make sure there was120vac, Power supply was good, installed new ice maker, connected plug. Works great.
Part to fix ice maker is very expensive, complete unit only $15 more and it has a one year warranty.

With a little investigation, I found that the ice tray had corroded, and the increased friction was keeping the ice from dumping out properly. It also had apparently damaged the gear motor, and the timing of the ice ejector was off. I went to the Part Select site and found that the icemaker specifically for my refrigerator was significantly more expensive than the universal Whirlpool replacement icemaker, but the two looked similar, so I ordered the universal replacement. When it arrived about 3 days later, I was able to easily remove the standard parts and replace them with the plastic parts and wire harness that were unique to my refrigerator. They fit perfectly, and I had the new icemaker installed in only about 20 minutes, including time spent to remove and replace the plastic parts

unscrewed 4-5 screws; unplugged; attached arm; installed; reverse pattern. truly easy. cost 1/3 what repair man quoted me. this is easy!

Removed two screws, pulled the element out and disconnected the wire harness. Reversed the procedure and we were one.
Kept a close watch n the ice maker to make sure we didn't have another flood. The first time an ice cube stuck between the metal bale and the side of the freezer--we had about 50 gallon of water on the floor. Thought we had it fixed and a few days later another flood. Decided to replace the unit and it is working great...Hopefully no more floods.