1066225120 Kenmore Freezer - Instructions

My fridge is a little different from the video model. The Controls in the fridge are located on an "arm" which swings down when the two screws are removed from the sides. It was not necessary to remove a front plate or knobs. However, I found when I got in to it that the old timer was not held by screws, but by plstic posts which had these "speed nuts" on them. This is a little metal plate which fits over the plastic post and bends to lock it in place. When you try to remove it, it acts like a barb, holding the little sucker on. I ended up bending the ends of those little suckers up tight against the post and twisting and pulling with needle-nose pliers. I broke one post like others before me commented, but one stayed intact. The only break at the top, so there ie still post left to hold the new timer. Once it was off, I was able to replace easily. The directions for choosing the right prong were a little confusing, but follow your gut and go with the wire colors. My schematic found in the bottom of the fridge did not look like any of the drawings, but I could match the wire colors. I also asked "Just Ask" for help, to make sure. My gut instinct was right. My fridge is now working again beautifully. If a housewife with no appliance repair knowledge can do it, so can you. I fixed my dryer with PartSelect too!I will never call another repair man until I have checked this site to see if I can do it myself. Bet I have saved $600 so far at least!

I did the repair just as your video showed me. It worked out great.

First of all the part was not located in the section of the refrigerator that was shown in the video. I wasted a lot of time taking that section apart only to find that the part wasn't there. After some investigation I finally located the defective part. It was behind a piece of sheet metal that had to be bent out of the way to unscrew the part. If I hadn't bent it out of the way, it would have been a major disassembly to remove the sheet metal. Once removed, the installation of the new part was fairly simple. The only confusing thing about the installation was determinig which of the prongs on the part that the internal wire to the new part was to be attached. There were 3 options given and the instructions were not very clear as to which one I should use. Apparently I guessed correctly because the refrigerator seems to be functioning perfectly since the repair.

I just simply eliminated the ice buildup with hot water and a knife. But I still have the Defrost Timer Kit for future use.

My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!

With the help of the website I was able to verify that the part I removed (in the area of the clicking sound) was probably the part required for replacement. I ordered it, installed it... IT WORKS (I knew it the moment I plugged in the power cord and heard the compressor kick on). Saved me from buying a new fridge or calling a repairman. I'm a 58 year old woman with no appliance experience. I watched the videos and installed the part without any trouble. Thank you PartSelect for your easy to use website instructions and helpful hints.

The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.

changed bulb

I just followed the enclosed instructions

First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.

I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.

Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.

opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.

Exactly how the part select video described it. Threw a little curve ball figuring out which timer setting to set it to. But the instructions provided with defrost timer walked me right through it. No problem. After installing part nothing happened for about ten minutes, which had me second guessing each and every step. Then, like magic, cold air began blowing. What a relief. Thanks so much, love this site. Refrigerator works like new!

Pulled refridgerator forward away from the wall. Remove the cardboard back behind the appliance.I saw that the condenser fan motor was not working. Unplugged the appliance from the electrical outlet. Removed a 3 wire plug from the condenser fan motor. Remove 3 screws (with a nut driver) which held the condenser fan motor in place. Remove the condenser fan motor from the appliance. Looked up the part needed for repair using the appliance model number. Found which part was applicable for the appliance. Placed the order from Price Select on a Monday morning and recieved the part 2 days later on Wednesday via FedEx. The item shipped was a 2 wire condenser fan motor. Read the instructions that came with the part. Using wire cutters, cut the old 3 wire plug. The center wire is a green and yellow striped wire. Use the same colored wire that is also shipped in the box and has connectors on both ends. Cut one of the connectors off and use the wire strippers to remove plastic wire coating. Connect both ends from the appliance and the green and yellow wire that was shipped. Use a wire nut (also shipped in the box) to connect the wires. You will have 2 black wires left on the new condenser fan motor that need to be connected to the appliance. You should have an orange colored wire and another wire that is black with a white stripe. Connect one wire from the new fan motor to the orange wire and use a wire nut to attach both wires together. Use the other black wire from the new fan motor to the black/white striped wire from the appliance. Use the wire nut to attach both those wires. Place the new condenser fan motor back in the appliance using the screws that come with the motor. Attach the green and white wire with the connector on the end to one of the 3 screws that hold the motor in place and secure the screws. Use the electical tape to hold the wires all together and away from the fan motor. Plug the appliance into the outlet. You can see the condenser fan motor working properly. Note that when connecting the 2 black wires from the new condenser fan motor to the orange and the black/white wire from the appliance, for my appliance, it did not matter which wires were connected as the fan motor was a clockwise motor. Place the cardboard appliance backing, back on to the appliance and push the refridgerator back in place. Allow about 5-6 hours to get the freezer to between 0-5 degrees. The refidgerator should be between 34-38 degrees and will take a little longer to get to that projected temp.