10651759710 Kenmore Refrigerator - Instructions

Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.

Access back of unit, lower left corner. Remove wire capacitor retention clip. Unplug cold capacitor, plug in replacement, reinstall wire retention clip, test.

System not cooling. removed back cover and notice fan not rotating. Looked up unit and found diagram. Ordered motor which was received in less than 5 business days.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.

Very simple fix, remove 3 screws, two connectors to the old switch

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

Ordered Ice Bin Auger and changed with no problem. Found how to change on YouTube and followed video.

We used the hair blow dryer to soften the gasket after being in the package. We laid it on our bed and made the gasket straight with the heat of the blow dryer. Then we began to install the gasket and once we installed it, the door would not stay closed.

Followed online video instructions

Took old ice maker out; put in new ice maker.

use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks

First I removed the screw holding the ice door shaft (at the rear of the ice container). Removed clip of which the screw was holding in place (no need to remove the clip from the shaft). Then I removed the front cover screws, separated front cover from ice container. Door shaft is removed with front cover assembly, no need to remove anything else from front cover. Pulled out auger shaft, removed circlip (snap ring) and washer from front of shaft. Used an adjustable wrench to remove plastic nut from front end of shaft. CAUTION - the plastic nut is reverse thread, make sure to turn it clockwise to loosen and remove. Pulled off broken auger then reassembled with new auger in the reverse order as previously described.

SUPER EASY. I pulled out the ice bucket and confirmed the motor ran and the axel turned - however the coupling was missing. Ordered the coupling - pulled out the ice bucket, screwed on by hand with minimum effort, put ice bucket back and ice started coming out the door. It took less than 5 minutes and no tools required.

All I did was unscrew the stripped one and screw the new part on. You just have to get it started unscrewing first ( remember that it's backwards! ).

(1) Ordered PS371704 from PartSelect! Best advice EVER! (2) Unplugged refrigerator (since the water solenoid on the back of the refrigerator is powered to switch ON the water, you NEVER have to turn off the water!) (3) Pull off the refrigerator's bottom grill. (4) With a small saucer under the fittings, unscrew the black and white tube fitting. There is only one nut to remove on the white tubing side. You'll need to undo the compression fitting on the black tubing and slide off the compression nut. You'll need to MAKE SURE you keep these nuts and replace onto the black and white tubing the SAME WAY you took them off. You'll NOT need to use nut drivers as finger tight is the key. Too hard and you'll ruin these plastic nuts. You should get only about 1/8 cup or less of water during this whole exercise. (5) Cut off the old, broken water nozzle. (4) Find a screw of the appropriate size to fit tightly 1/2 way inside the new tubing (this is to ensure your old and new tubing are connected to feed through the door). If screw is not tight within the tubing, wrap part of a plastic (thin) sack around this screw a couple of times and force into the tubing. You'll, of course, then need to use the hacksaw to cut the head off the screw as you'll be forcing the other half of the screw into the old cut tubing (6) Chase the dog out of the kitchen and cajole your wife (significant other) to push the newly joined tubes through the top of the dispenser, through the door and out the bottom as you will be gently PULLING on this old tubing from the bottom until the new tubing pops through the doors bottom. (7) Once this new tubing is out, you will separate the old tubing and, using the nuts in the proper sequence, connect this new tubing to the white tubing. (8) Plug the refrigerator back in and test flow the water. Check to ensure the plastic nuts have no leakage ... button up the bottom grill ... and enjoy the fresh water! PS> Don't forget to praise the wife (significant other) and give the dog a treat for staying out of your face!!