10651132210 Kenmore Refrigerator - Instructions

I removed the filter from the box I took the old filter out and inserted the new air filter put the cover down and that was it.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

After pulling the fridge out and removing the dust cover over the lower portion in back of the fridge, I could see water dripping from the inlet valve between the water main to the icemaker and the water dispenser in the door.
1. Unplug the fridge
2. Place a towel under the fridge to absorb any over flow
3. Turn off the water supply to the fridge - this is usually at a tap valve on the cold water line. trace the line from the back of the fridge to find the connection point. In the unlikely event there is not valve at the tap valve or if it is inaccessible, turn off the main water supply. If you have to turn off the main supply turn on a faucet somewhere in the house to bleed the pressure from the line.
4. If the valve is tied to the frame or line , undo the tie or cut the zip tie (in my case)
5. Unplug each electric connector from the old valve to the new one.
6. The water connections are all quick connect so release the intake line by pressing down on the white ring and removing the tube. Press the tube into the new valve.
7. Repeat with each line going to the refrigerator making sure to plug each tube into the same outlet you pulled it from
8. In each case to minimize water coming out of the tube, hold your finger over the end while transferring to the new valve.
9. Verify that all tubing ends are FULLY pressed to the valve
10. Turn the water back on slowly and check for leaks. if some are seen turn water back off and repeat steps 6 thru 9.
11. Plug fridge in
12. Run water from the door faucet to bleed any air out
13. Clean up any spillage
14. Replace dust cover (if present) and replace refrigerator in place
Piece of cake

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.

The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!

Very simple fix, remove 3 screws, two connectors to the old switch

Ordered the part. It came a day later. Unpacked it and put it in the door.

After finally getting the wright parts sent to me I took out old bin added the parts to the new bin slid it in and I’m done.

Open door and from appliance instruction book
Replace filter

Open the refirigerator door and push and hold the On/Off button at the top to turn off internal power. Open the freezer door and move the icemaker switch on the right side freezer wall to "off".

To get access to the icemaker, first remove a hinged plastic door that mounts to the ceiling of the freezer compartment by two hex screws. Remove the screws and the door so you can work with the icemaker without interference.

The icemaker assembly will slide out once the wireharness has been disconnected. To disconnet the wire harness, a while plastic shield has to be removed from the right side of the icemaker, just behind the water inlet.
Locate a hex screw on the bottom right rear of the icemaker and remove it with a socket wrench. Then the plastic cover can be pulled off.

Slide the icemaker out enough so you can get your fingers on the plug connector. It takes some effort to pull the plug connectors apart. Once unplugged the whole icemaker assembly can be removed.

The motor module is located on the left side and is protected by a white cover. This cover is not attached so it can be pulled off to reveal the motor module.

Remove 3 screws from the outside of the motor module and the module can be pulled out of the housing. Insert the new motor module. The module turns the shaft of the ice srapper arm. the shaft has a D shape which mates with the hole in the motor module so you may have to roatate the scrapper arm until the shaft shape matches up with the hole shape in the motor module.

Once the motor module is seated, replace the 3 screws and push the white cover back on.

Position the icemaker so you can reconnect the wireharness plug connectors. Once connected you can push the icemaker asembly back into the grooves of shelf rail. Reattach the while protector shield which covers up the wire harness plugs.

Open the refirigerator door and push and hold the power button to turn internal power back on. Move the icemaker switch on the right wall of the freezer to the "on" position and close the door.

The icemaker should start making ice within 2 hours.

Unpack, wash in warm soapy water, slide into pkace

At first ordered the wrong part. Using the website was difficult to find the correct part, but once I called, it was pretty easy to find the part needed. Part showed up and install was only a few minutes. No more leaking!

Thanks for the help PartSelect!

Originally I took the module off and found that a small plastic part had broken. Both pieces were still there, so I super glued them together and reassembled the unit. It worked great for a couple months. I realized it needed a more permanent fix, so I found the model # and looked up the part. That was very easy on your website. I ordered the part expecting it to take 4-7 days. It was at my house in two days! 15 minutes later I was makin' ice, and makin' my wife happy. Thank you for an all around great experience. I'll definitely buy from you again.