10651129212 Kenmore Refrigerator - Instructions

simply slid out old damaged/taped up shelves and slid in the new ones i ordered,

I removed the glides under the edges of the meat pan, remove the old pan, put the new pan in and replaced the glides. I was very pleased with PartSelect. I ordered my part, and it arrived the very next day. I will definitely order my next replacement part thru PartSelect.

Be advised that to do this job, you have to take the ice tray and feeder assembly completely apart. The only tricky part is that the nut, part 31 in the drawing, that holds everything together is reverse threaded. Since it's plastic, you're afraid you'll break it. If you know it's reverse threaded to begin with you can go ahead and apply the required force to get it off.

I was not able to unplug the refrigerator because it is housed in a built-in. I removed the icemaker and following simple instructions from YouTube was able to pry the cover off the existing part. After a few gentle tugs, I disconnected the pinned wires from the old part. Connecting the new part was a little tricky but I managed with a little contorting. As soon as the pins connected the freezer light as well as the refrig lights came on. It took about 15 minutes to complete.

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossreferenced to new part number which was correct the first try. Thank you!

simply removed wires from the old motor and gently lifted it out by by the metal clips - put the old bracket on the new motor, snapped on the new fan, replaced the wires, reinstalled the shield. All done in about 15 min.

Same as everybody else on this post. Real easy. Actually, I just wish I would have done it sooner.

That was due to the evaporator blocked by the ice. Check found the defrost timer is okay. The next thing I can think of is to replace the Electronic Control Board which is installed in the fridge side top compartment. Ply open the face cover, remove the nut and screw that secure the EC Board. Pull out the cable, mount the new card and re-connect. So simple. It is back in order.

This company is WONDERFUL! I ordered the wrong drawer the first time, but their return process was a snap and the correct drawer arrived the next day. It's great to know that there is someone out there with just about every part you'll need for about any appliance that is truly customer friendly.

I tried to replace the light in the fridge first but couldn’t get it out (that one has the control board and is very expensive) so a replaced the one in the freezer by prying it off the ceiling. When I plugged the new one in all the other lights came on full power. Strange but I sent the other one back.

remove shelves in freezer compartment incl.holders(slide up to remove)
Remove lamp/shield
Remove panel (six phillips screws)
disconnect motor
pull off fan blade
squeeze bracket holding motor to remove
remove motor.
Re-assemble (in reverse)

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repair man. He would have made two trips since he would never have had this part with him.

I originally ordered the led light control board but when I hooked it up I still had the same problem. My neighbor checked both door switches with a voltmeter and they were both good. I then ordered the light for the freezer and when hooked up the problem was solved. All lights worked. The freezer light has four tabs that allow it to snap into the roof of the freezer. Those tabs can be hard to see because there isn’t much room. I used a mirror to locate the tabs and a small flat tip screwdriver to push the tab over and removed the light.

New part slipped right into the studs and fit perfectly

Took off the cover, pulled out the old filter, inserted the new one and closed the door.