10651123210 Kenmore Refrigerator - Instructions

Emptied draw of contents pulled draw out and inserted new drawer....easy pea-zee

using a flat blade tool removed old main light board and installed new light board, light now works fine.

i replace the old broken one, very simple and easy,thanks very much for the part, the price was really good better than sears, they were charging me for the same pretty much $100.oo, so thanks for everything, the time frame delivery was excelent!!!!! so i'll be keep you name first on my providers list for my next job......!!!!!!!
sincerely;
wilfredo Uztariz

First I removed all food in freezer.Then removed selves and hanger brackets.Then the back panel and light cover.Then I unplugged motor but before this I unplugged refrigerator from the wall.Removed motor from bracket after pulling of fan. Reversed the order to install motor and put back together

Watched a video on how to disassemble the old bucket and reassemble the new one. Piece of cake. Thank you for the part and how to video.

Henry

Previously replaced the Fridge light (control board).. The Fridge and Freezer lights were flickering rapidly...LIghts worked fine for four months...then the freezer light went out completely and the fridge light went dim. I unplugged the freezer light and all lights went out! Hooked it back up and ordered new freezer light. After replacing freezer light all three lights work perfectly at full intensity problem solved...For now!

Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .

The repair consisted of lifting up the drawer cover and replacing it. Why the 60 minutes to do that? It took 58 minutes to clean the refrigerator.

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind the picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

First, imagine the frustration - I want an apple.... can barely open the drawer. Need carrots - the struggle. Celery? Wondering if I can do without..... the drawer's plastic has broken along where it slides along the guide rails, and it was a pain to open and close the drawer. First, as is my custom I went to Amazon, but couldn't find the part. There, however, I read a useful customer review that told me how to find the correct item, so I did that, input the part number into google, and VOILA - I got to this website. Excitedly, I input my credit card information and waited with eager anticipation (and a bit of trepidation - would it be the correct size?) for the drawer to arrive. A short time later, I found a large box at my front door. With joy, I took some scissors and opened the box, and then carefully used the scissors to cut the binding strap that was holding the protective cardboard wrap. My new drawer!! I gave it a quick clean, and then opened my fridge door all the way (this is an important step). I pulled out the old, broken drawer, and carefully inserted the new. It fit perfectly!! This took about 15 seconds. I then took those apples, carrots, and celery (and a pomegranate and some lettuce) from the old, broken drawer and placed them tenderly into the new drawer. I slid the drawer closed, and then shut the fridge door. Mission accomplished! Last step was to throw the old broken drawer into the garbage - this was a very simple process as well.

easy peezy - removed old light/module and installed new one works great.

bought a new crisper drawer

(1) Remove the drawer by pulling it open until it catches. Push up gently on the bottom-rear of the drawer to lift it over the stop tabs in the drawer rail, and pull the drawer out completely. Note: You will need to push the refrigerator door gently to the fully open position to remove the drawer all the way. The door will open about 30 degrees further than where it comes to rest on its own when opened.
(2) Remove the shelf by lifting gently on the front and sliding it forward. Once the rear corners of the shelf are beyond the upper lip of the shelf rail, you can lift the shelf out of the rail, and turn it vertical to remove through the fridge door. Note: the glass in the shelf is meant to stay in, but if its old or damaged it may tip out when you turn the shelf on its side. So you may want to tape it in place before removing the shelf.
(3) Install the new shelf by repeating step 2 in reverse.
(4) Reinstall the drawer by repeating step 1 in reverse.

Remove back side cardboard access cover. About 6 dcrews need to be removed. Remove 9/16” bolt and lower compressor tray frame down to slide out wheel axel. Place wheel in slot and replace axel. Lift compressor tray and replace 9/16” bolt. Replace cardboard cover. Remove 2x4.

took the auger off and baffle replaced the baffle put every thing back together installed back to the freezer tried it out it dont work have to tear into the the motor which works the auger to see if anything else is broke.