10651113711 Kenmore Refrigerator - Instructions

I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights were staying on (50 watts of heating). Replaced the switch and the frig started working like new.

After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.

removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.

Great service. Unpluged old switch and pluged in new one. Works great

Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.

Pry old switch and pull out. Disconect two wires. Put two wires on new switch, must be inserted right and connections not loose. Put switch in, making shure wies do not come off and snap in place

Unplug appliance. Socket wrench to unscrew two screws. Module drops down. disconnected two press-on wires by prying off with screwdriver. Removed old switch. Press-fit new switch. Reconnected two wires (color coded). Screwed module back in place. Plug in appliance.

Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.

removed ice bin from freezer then removed front from ice bin then all i had to do was remove e clamp from end of shaft that made it possible for me to remove the ice crusher parts then slide off the drum. all that was left was to put back together.

I began by removing the ice maker and storing the ice. The part did not come with instructions so I began taking the ice maker apart. I ran into problems rather quickly so I went to the "part select" web site and there was a video with instructions on removal and reinstallation of the auger. It was a breeze after that. These guys are obviously professionals!

Had to replace the auger drum. Went fairly smooth. The video that was linked next the part was a big help, especially when all the blades of the ice chopper came off of the shaft at once and I needed to get them back in the correct order. I did a freeze frame on the moment in the video to figure out the order.

Took the Ice Bin Out emptyed it then removed the nesasary screws pulled the broken Peice off and sliped
the new part on held the metal peices together so we would know how to keep them in order for fear of putting them in wrong place but we did it now it works great thank you so much for getting the part to me so quickly your great.

It was a breeze to remove and replace. Made even easier by the previous DIY guys posts. Make sure you turn the nut at the end of the shaft clockwise to loosen. Taking a picture of the blades for ice crushing before removal for future reference is a great idea. It wasn't hard at all. Just take your time.

We took the icemaker apart, and took pictures of how it looked before so we knew how to put it back together, we were really surprised how easy it was to put back together, I will be ordering other parts from this company, I got my part in 1-2 days by Fedex, I will be telling others about this company

A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.