10650042717 Kenmore Refrigerator - Instructions

Removed all ice from bin and let it thaw. Removed all screws and nuts from the front to release the ice crusher and the long bit. Had already printed out all the advice from others on the on-line section about taking photos and not getting the crusher blades out of order. Removed the clip with needle nose pliers and the washer. Removed the blades laying them down in exact order and direction they came off. Put on the new auger drum and reversed everything. It was nice to know that the plastic screw that held the clip is a reverse thread, otherwise we might have broken the dang thing. Too bad there aren't instructions with the part when you get it instead of just a diagram. All-in-all, it went well.

I could not have done it without reading the repair story about this same issue. I DID take a digital picture before taking the blades out and that was helpful. NO ONE, except in the repair story, ever mentioned the reverse screw to get the blades off. It simply made it possible for me.
I fixed it!!!! I am a 69 year old widow who loves crushed ice, so I am happy!!
The PartSelect service is great!

First, I removed the 6 screws which hold the ice bin to the drum and the front cover. I then removed the screw which holds the door lever and bracket to the ice bin. Then I took the C clip and washer off the end of the auger to remove it from the housing. I removed the plastic nut to remove the auger drum from the auger shaft, being careful to place the blades on the table in the order they were removed. I then installed the new auger drum on the shaft and re-assembled everything in the reverse order. This was really easy for me because I had replaced the auger previously. (about 2 years ago)

The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!

Looked up on you tube to verify and see "secrets" to installation.

watched video on your website and followed directions

Ordered Ice Bin Auger and changed with no problem. Found how to change on YouTube and followed video.

System not cooling. removed back cover and notice fan not rotating. Looked up unit and found diagram. Ordered motor which was received in less than 5 business days.
Replacement was super easy. Just unscrewed from frame, pulled off fan, put fan on new motor and remounted back in frame. Took 10 minutes tops.

Removed the old ice maker by taking out three screws. Unplugged the electrical connection to the old ice maker. Replaced the old ice maker with the new one. Reconnected the electrical, replaced the screws, and reset the new ice maker. The replacement part has been working perfectly. This was an extremely easy replacement job!

We removed the old switch, unplugged it, plugged the new one in and it was easy to do. But when we tried to put the switch back in we had a very hard time doing it. Eventually got it in, but if it had not been for the difficulty we had getting the new switch to snap in to place, it would have taken under 5 minutes.

I just followed the excellent Video for both parts. The door gasket is tedious but doable, just take a deep breath and press on. Putty knife is handy to push edge of gasket under the plastic lip. The closer devices take 3 minutes - simple R&R. Check the videos - they're pretty clear and detailed.

Replaced motor it was not issue. Now I am stuck with a $300 motor I cannot return. When I say will not dispense ice everyone thinks it does not make ice. Auger does not turn to push ice out the door. Reason I thought it was auger motor when you push lever on door the auger turns about one eight of a turn. So, it would seem it is getting signal and power. Cannot find any articles on this specific issue. If anyone has a suggestion, please share.

First I removed the screw holding the ice door shaft (at the rear of the ice container). Removed clip of which the screw was holding in place (no need to remove the clip from the shaft). Then I removed the front cover screws, separated front cover from ice container. Door shaft is removed with front cover assembly, no need to remove anything else from front cover. Pulled out auger shaft, removed circlip (snap ring) and washer from front of shaft. Used an adjustable wrench to remove plastic nut from front end of shaft. CAUTION - the plastic nut is reverse thread, make sure to turn it clockwise to loosen and remove. Pulled off broken auger then reassembled with new auger in the reverse order as previously described.

Disconnect plug from wall. Insert putty knife between light switch.and trim panel , apply pressure to depress plastic spring holding switch in place. Apply a slight twist too putty knife releasing switch from trim piece. This wil expose plug connected to switch. Disconnect plug from switch. Connect new switch to plug. Insert switch into trim. Plug refrigerator into wall socket.

Popped out broken switch with blunt flat edged instrument. Disconnected switch from unit . Plugged new piece in and reinserted into side panel of refrigerator. Very easy.