10644254400 Kenmore Refrigerator - Instructions

From the time I started to finish I worked 3 hours, this included installing the new ice maker, cutting into the cold water line in the basement and installing a t with a 6inch piece of pipe with a compression valve to connect to the small cooper tube, this is worth your time to do it this way, its a lot better connection than the small pierce valves that come with the kit, they will leak over time. I installed the filter in the waterline in the basement for easy access

I noticed that everytime I plug the refrigerator cord into to the wall outlet it would trip the shock prevention safety switch on the wall outlet. I came to the conclusion that something was blocking the electrical current to flow to the compressor. I figured if I changed the the part attached to the compressor then the electricity would be able to make a complete circuit to the compressor. so I got the part # from the old part and I researched it through your company. You had the part in stock. I ordered it and it was at my door the next day. It worked extremely well. I proudly can say I did it myself and most importantly I don't need a new refrigerator and I save a lot of money. thanks I will definitely use your company in the future. Ray

I just slid the new pan in , partselect has the correct part all the time , I repalced my ice maker once and it took 15 min no problem

Whirlpool refrigerator laid down on us on a Friday morning. Local repair center would not be out until Monday noon. $89 service charge plus labor and parts estimate. Golly Miss Molly! Diagnosed problem through PartSelect forum and ordered the part at 2:50pm that day[Fri]. New compressor part arrived at 2pm the next day [Sat].INCREDIBLE delivery time!Up and running 10 minutes later. Thanks PartSelect. My faith in Corporate America{gosh,maybe even mankind] has been restored.

First I removed all contents from inside refrigerator door.Then I removed (1) 10mil screw,which holds cover for top hinge.Next I removed the (3) hinge screws,and lifted door off of bottom hinge.Pulled off plastic closure cam from bottom metal hinge post.I cleaned metal post ,applied a small amount of vaseline to post, slid on new plastic cam,installed door, replaced screws.Very easy,10 to 15 min tops.

Using a 1/4" nut driver and a philips screwdriver I removed all the screws in the shelf brackets and coil cover and removed coil cover. Removed fan blade and then faulty motor (held in with clips) Installed new motor-two wires (power) and ground (green) pushed fan blade back on and tested, then reinstalled all panels and shelf brackets.

Just replaced the switch, but unfortunately that was not the problem; nor was it the bulb....so I am back to square one.
But Parts Select is a great place to order from. Thank you.

I removed the two screws that were readily in view. I then figured out the there was a faceplate which I was able to pry off after removing the temp control knobs. The temp control unit was easily accessible and was held by two screws which I removed with the nut driver. The only difficult part was replacing the plastic tubing which covered the sending unit.

Remove old tray, replace with new tray.

Simple & easy.

Best part is I ordered on Monday & received on Tuesday!

plastic warped in ,spaced out and, the socket snapped back in place.

The broken part was removed and new part installed without any trouble.

I followed your instructions , the only thing that was left out was that the freezer has a drain hole that had to be thawed out with a hair dryer,till the water went to the drain pan underneath the ref. your instruction were through enough, that's why I purchased the part from your company, I installed the part 2 days ago and its working like new again 23.00 for the part instead of 1200.00 dollars for another ref. thanks very much. 6 months ago I purchased the relay and compressor starter from your company at that time per your instructions I shook the compressor starter and like a light bulb it had something broke inside,I needed that thanks again oomk

Took off refrigerator door from top hinge and lifted off. A little difficulty getting worn out parts off (needed dremel to drill out worn plastic); replaced with new parts, the screw head holding on the part was starting to be worn as well but still worked. If I hadn't got to this repair soon the bottom of the door aluminum would have total worn out as it is, it has a deep groove but not noticeable. The new cams also force the door closed tight instead of slightly ajar at times.

I took off the front cover with the controls. Pulled out the control knobs, unbolted the assembly (which was identical to my replacement part) and proceded to follow the old thermostat tube to the back of the fridge. The tube should be carefully removed, not pulled on, there's a couple of screws holding it in towards the back. I installed the new part in reverse of how I took out the original part. I'm very happy with how the fridge has come back to life! It was much cheaper to fix it than to replace.

Very easy. Take panel off and replace motor.. All wires matched fine. Easiest applance repair I've done..