10640263010 Kenmore Refrigerator - Instructions

From the Expanded view on the website, I chose the bin -I thought. The expanded view picture is too small and I got the shelf instead. -But a phone call got everything back on track.
Repair involved a knife to open the box!

Simply slid out damaged shelf and slid in new one

Just replaced the broken one without using any tools.

Removed shelves from frig and freezer. Removed cover over evaporator core in freezer and removed loom. Replaced thermostat by cutting out and connecting new part with connectors. Remove console in frig and replaced thermostat for frig temp. Also had to remove channel to expose freezer rod and capillary tube for thermostat. Took extra care not to kink tube. Reassemble both sides and adjusted correctly and plugged in. Both settings at normal and frig is repaired now. Obviously it took awhile for frig to get completely back to freezing and cold temp. Remember frig has not ran for days. Compressor cycles correctly now also.

just added new shelf - perfect fit

bought a new crisper drawer

It was a drawer I removed the old one and slid the new one in. Took longer to fill out this form than to replace the drawer

The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.

The repair was super easy. It took all of 10 seconds. From ordering the part to repair, I would use part select 100%! Excellent company with excellent parts. Thank you!

Followed easy installation instructions which were helpful

(1) Remove the drawer by pulling it open until it catches. Push up gently on the bottom-rear of the drawer to lift it over the stop tabs in the drawer rail, and pull the drawer out completely. Note: You will need to push the refrigerator door gently to the fully open position to remove the drawer all the way. The door will open about 30 degrees further than where it comes to rest on its own when opened.
(2) Remove the shelf by lifting gently on the front and sliding it forward. Once the rear corners of the shelf are beyond the upper lip of the shelf rail, you can lift the shelf out of the rail, and turn it vertical to remove through the fridge door. Note: the glass in the shelf is meant to stay in, but if its old or damaged it may tip out when you turn the shelf on its side. So you may want to tape it in place before removing the shelf.
(3) Install the new shelf by repeating step 2 in reverse.
(4) Reinstall the drawer by repeating step 1 in reverse.

I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull the connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!

First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver removed the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!

I was told to order the run capacitor and the technician thought it would repair the refrigerator; but it did not. The appliance technician had to take the run capacitor off and install what he called a "hard start" and the refrigerator is operating right now.

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.