10632943101 Kenmore Refrigerator - Instructions

Take screws out pull panel out unconnect the part connect new one and your done

Like you video

Ice maker fit perfectly over 2 top screws. I tightened them and put the one on the bottom. I was done in less than 10minutes. Everything fit perfectly as expected. Couldn't have been eaiser. Parts Select is my go to online store.

I turned breaker off to fridge, it was easier than pulling fridge out in camper. I took 4 screws out of back panel that revealed the evap fan, took 2 more screws out to take fan bracket off. Unplugged fan plug. Took fan blade off the non working evap motor and put it on the new evap motor. Put all the screws back in the reverse order and flipped the breaker and air started circulating.

Removed door and replaced bushing bracket was ok.

I attached the hinge and secured it with screws and socket wrench.

Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now

inst said,"50 pct of the time this calls for new capacitor," so we changed the capacitor. Same prob. It also said,"25 pct of the time it's the bi-metal thermostat" So we ordered it. We removed the plastic rear panel from inside the freezer comp. using small nut driver. Here we found much ICE surrounding the defrost unit, three inches thick. We thawed the whole mess. and the freezer has worked fine ever since. I think my habit of getting ice cubes from the inside container rather than from the ice cube dispenser, had kep t the freezer door open too much, interfering with the normal defrost cycle and allowing ice to build up over time so that it finally defeated the system. My new rule, "get ice cubes only from the front."

Removed the old gasket and ran the hard edged lip into the opening behind the door liner. Concerned that the gasket does not seem to be attaching itself to the door well. First put it on the side of the refigerator and it would not adhere enough to support itself. While it closes it just doesn't seem to attach with the magnets in the gasket. These magnetic strips have a weak magnet side and a strong magnet side. I wonder if they put the wrong side facing the door when they assembled it. Counter this with a new gasket for an upright freezer which was twice the length and attached itself firmly to the side wall of the freezer and did not slide down.

I suspected the frig thermistor so I cut wires to the original. The new part was not a direct replacement, but was adaptable. I’m not sure the frig design would allow for an OEM replacement anyway. I clipped off the useless connector on the new thermistor and spliced the thermistor in by soldering wires appropriately. That was a bit difficult due to the short available length of the wires, and it didn’t solve the problem. Since it seemed like the damper responded normally to power-off resets and diagnostics using the onboard control buttons, I decided the main control board pretty much had to be the culprit. It was. Replacing the board was a piece of cake. Only a 1/4” nutdriver required, plus maybe a small screwdriver for prying here or there. Happy to have the frig working again.

Remove food from freezer shelf and ice maker back panel4 screws remove old motor replace with new motor reinstall all removed parts. Plug in and fan instantly came on refrigerator working great since

Inserted scraper behind gasket breaking it free from door, permitting a hand hold. While putting tension on gasket, slid scraper around door gently removing old gasket. Replaced gasket starting at top gradually working around door. No need to remove door.

I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.

Was told capacitor was problem 90% of the time.Capacior was not the problem.Bad start relay.

Not so good that was not the problem. Fan is not seized and all the lights work and display is not on but lights up as well. No start once plugged back in after 15 minutes of being unplugged. Nothing same no change.