10632243101 Kenmore Refrigerator - Instructions

Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

shook bottle and painted waited a day and repeated

Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.

Unplugged refrigerator. Unplugged ice maker and took out three screws holding ice maker. Put new ice maker and attached three screws. Plugged ice maker in. Plugged refrigerator in and ice maker began working. Threw out first ice cubes made. Unit now working fine.

Removed/replaced ice maker and valve per enclosed instructions. If you can service your own lawn mower this R&R should be easy for you.

Per instructions

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

remove fiber grill cover, remove large bolt holding under frame ( with a 2X4 block, place under refrigerator on outside edge so frame can drop down.) remove pin from broken wheel, replace reversing proceedure. Note: when blocking refrigerator, care must be taken not to let block extend under entire frame. it only needs to be placed approx 3/4" under edge of refrigerator.

the repair it good and easy ,vo helper to do it.

Instructions came with the part I ordered and they were very easy to follow. Basically you have to remove the cardboard cover from the back. Then you remove the four screws at the bottom (2 front, 2 back) that hold the bottom plate on. My husband tilted frig and held it while I put a block(4" x 1/2") under the bottom outside frame (not the bottom plate). You can see a ridge on the frame which is where I placed the block. My husband braced the frig the whole time I did the repair just to ensure it didn't fall on me even though it was blocked. The bottom plate didn't slide back at first. I took a flat screw driver and hammer and slightly tapped the bottom plate through the screw hole that secures the bottom plate to the frame. I tapped 2 or 3 times...gently each tap...until the bottom plate dropped down. Which was the 1/2" noted in the instructions. I then was able to access the front wheel, remove the pin and replace with the new one. We replaced both front wheels so I did not replace the bottom plate until we replaced the second wheel. We removed the block and tilted the frig to the opposite side, blocked then I replaced the second wheel. Once that was done I removed the block, my husband let the frig down gently and I went to the back and tapped the bottom plate forward. It didn't quite want to go back in place but with patience it finally and then was able to put all screws back in. Donna

It was so easy. This is the second Ice maker we have put in this fridge. Thank you very much.

I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent items in the fridge from being able to touch. Bad solution.

Added ice maker to our frige as i have never done one so i called a friend and he came over once we figured it out took less than 1/2 hour to install and run water line only thing instructions could have been a lettle clearer to under stand plus i called sears and they wanted 160.00 dollars for just the icemker this did not include the shut off arm or the bucket to catch the ice and there was no screws to attach it to the inside of the freezer you guys saved me $70.00 if not more and got more for my dollar thank you very much over all pretty simple check parts select before going to like sears or any place like them much cheaper here thanks

The fridge was prepped for an ice maker but was never installed. After much aggravation of people not filling the ice trays I gave up and installed the ice maker. This is probably the hottest summer on record, and we were going thru a lot of ice. Lost a little real estate in the freezer by the ice maker but it was well worth it. Now I know I have fresh ice for cocktails in the evening!Install was fast and easy. A little longer than usual because I had to run the water line as well.