1041-002A Frigidaire Dishwasher - Instructions

Removed the old rollers with with screw driver. Used the original screws and washers, and reinstalled the new rollers. Had been having trouble with top dish rack metal slides popping out of the old rollers. I not that the replacement rollers are slightly larger and have slightly deeper groves for the slides. Have not had the new rollers installed long enough to see if they remedied the problem. Will know in a few weeks time. So far, so good.

The repair was simple. When the part comes, you may need a hairdryer to heat up the plastic a bit to get any kinks that may have happened during packaging or shipping, very easy 5 minutes. Removed the old gasket by hand, very easy, 1 minute. You will need to clean out the track that the gasket sits in. Mine had years of black gunk inside of it. You will need qtips or a small screwdriver with some tissues or papertowels, easy but took 15 minutes to clean out properly. Installed new gasket in the track, start at the top middle, there is a notch on the gasket so you know where the middle is. Installed by hand, just push bottom edge into the clean track, easy 5 minutes. Ran the dishwasher with no leaks. Very pleased with the result and how easy the gasket was to remove and install.

Removed the service panel below the door (4 hex-head screws), then reached in and took the old broken spring out (right side) and hooked the new one up.

Glad I bought 2 springs - the other one (left side) broke about a week after I fixed the first one! Replaced it the same way. Helps to have small hands - you can't really see where you're putting the springs but can feel where they should go.

very simple to do....attach spring to door...stretch to hole in frame and attach there...easy as 123

In about 20 minutes, I was able to remove the front panel and access the springs. Besides a hard water line in the way, it was a snap.

I had to replace the door gasket but it would not go in very easy..So I put the gasket in a sink of warm water so it would be more pliable. Then it went on fairly easy.

Removed two screws holding the dishwasher in place under the cabinet. Pulled the dishwasher out to expose the door springs. Removed the old springs and installed the new ones in just a few minutes. Pushed the dishwasher back into the cabinet and replaced the screws. Job done.

I snapped on the new roller and bingo! problem solved.

Two rollers on the lower rack were missing and one was flattened. I popped off the bad roller and snapped the three new rollers in place, all by hand. Took about 60 seconds.

I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!

Snapped the new one in. One second repair - like new.

used the pliers to grip the end of the spring, extended it and removed it from the door and frame. The install then followed. It takes longer to remove the front panel than to do the repair.

So easy it shouldn't even count as a repair, really. The dishwasher, there when I bought the place, had a lower rack that wouldn't roll out as it should. That's because there were no wheels on the left side.

The rack lifts out easily. These wheels snap on to small protrusions from the wire rack.

I pulled the old door gasket out, cleaned the guck out and pushed the new one in it's place.

Snapped new wheels into place on the axel. New wheels were exactly like the old ones