1033248210 Kenmore Range - Instructions

The stories posted on your web page are great - only improvement would to add a schematic of the parts being removed - no issues were encountered - great service by the way - part arrived the next day - a Saturday!

John M.

removed screw from heat sheild, unpluged igniter and tested for 110v on wires feeding igniter (ok). removed bad igniter,ordered new one and installed with 2 - 1/4in. hex head screws. cut old male and female plug ends off old igniter, and wirenutted onto new igniter. turned on oven and it works fine. but noticed after oven burner lights, igniter stays on the whole time oven is on. I would think that it should go off when burner lites. Does anyone know if this is normal operation?

simple remove & replace. 2 min job. Couldn't be happier.

I took the old igniter out and replaced it with a new one.

Removed oven racks
Remove oven bottom
Remove 2 screws holding the glow coil onto the burner
Install the new glow coil with the furnished screws
Reinstalled the 2 wires back where you took them off

Replaced the old igniter with new one in 15 minutes. Popped the door off, took the bottom plate off, unscrewed the igniter and disconnected wires. Put the new igniter in and reversed the steps.....piece o'cake! Works great now!

Removed bottom tray of oven, removed ignighter, unplug two wires.

I removed the oven racks and the bottom cover. The bottom cover had 2 hand tight screws. Then I had to remove the silver sheet metal plate attached with 1 screw. Then I removed the 2 small screws that held the old Igniter in place. Then removed the 2 wire nuts connected to the oven wires. The new igniter fit in the same place as the old and I attached it using the same old screws. Then I connected the wires using the new wire nuts provided in the igniter kit. After testing the new igniter by turning the oven on to 200F, i replaced all the parts i removed including the silver plate the oven bottom and the racks.

I removed the bottom drawer from the oven, took my handy nut driver out and removed two screws from the round igniter. When it was loose from the oven I removed the two wire nuts conecting it to the power sourse, I reversed the process and it was working again. One thing did go wrong my wife made me clean the oven that wasn't part of my plan :)

frist tested ignitor with meter removed ignitor order
part , I recieved to my surprise next day I'm a very happy person

The biggest problem is to get down low enough and far enough back to be able to reach the igniter. Other tan that , it was a simple affair.Unscrew the old one and detach the wire nuts and reverse the procedure for the installation and hope the gas valve has'nt been affected

1) use screwdriver to remove screws securing lower pan in oven (screws are at back of oven)
2) remove lower pain to expose igniter and burner
3) remove lower storage drawer
4) disconnect 2 igniter wires from where they are attached underneath
5) use nutdriver to remove burner from above and below (this makes it easier to remove the igniter)
6) use nutdriver to remove the faulty igniter
7) cut off clips from faulty igniter leaving enough length to strip and then attach with ceramic caps to new igniter. (be sure you attach the right clip to the right wire)
8) reverse the process to install the new igniter.
20 minutes tops

Removed the three screws from the top and bottom of the oven door. Removed the outside door cover from the inside door panel. This gave me access to the six screws that hold the two sections of the inside panel together. The glass of the inside oven window was manufactured without the installation of retainers to keep the window from moving. I installed the four retainers that I purchased. Reassembled the door. The glass now stays in place. Since there were no retainers to begin with I had to figure out how they were to be installed to prevent the glass from moving around.

Using descriptions provided by others at this site, I replaced the old igniter with the new one very easily. Since this was the second time this oven has needed a new igniter, I did not need to cut the wires as described. Instead, I just disconnected the old igniter wires and rewired the new igniter wires. Replaced all the items I'd removed and the oven functions just fine.

Moved stove out from wall and unplugged 110 cord. Removed broken igniter from broiler with nut driver. Removed protective cover from back of stove. Cut off plug from existing igniter wires on the back of the stove. Installed new igniter and fed wires trough to the back of stove and connected the wires with the supplied wire nuts. Reinstalled protective cover on the back of the stove. Plugged the 110 cord back in and returned stove back to the original location.