Part Location Diagram of 131775600 Frigidaire Blower Housing with Blower Wheel
See part F10 in the diagram
Replacing your Frigidaire Dryer Blower Housing with Blower Wheel
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

Blower Housing with Blower Wheel

★★★★★
★★★★★
10 Reviews
$161.95
  In Stock
PartSelect Number PS418726
Manufacturer Part Number 131775600
Manufactured by Frigidaire
Product Description

Blower Housing with Blower Wheel Specifications

***Please Note: This part is a substituted part by the manufacturer. It may appear different, but should still work with your appliance.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Part Videos

Replacing your Frigidaire Dryer Blower Housing with Blower Wheel

Replacing your Frigidaire Dryer Blower Housing with Blower Wheel
Troubleshooting
This part fixes the following symptoms:
Noisy
This part works with the following products:
Dryer.
This part works with the following products:
Frigidaire, Kenmore, Westinghouse, Crosley.
Part# 131775600 replaces these:
AP2107606, 823074, 131775600, 131775610
Back to Top
Customer Reviews
Average Rating:
★★★★★
★★★★★
10 Reviews
5.0
Filter By Rating:
  • 5 Stars
    10
  • 4 Stars
    0
  • 3 Stars
    0
  • 2 Stars
    0
  • 1 Star
    0
  • 1
Sort by:
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
  • 1
Customer Repair Stories
 Average Repair Rating: 2.6 / 5.0, 8 reviews. What's this?
  • 1
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
Had 2-seperate problems; 1st was a high pitch squeel, 2nd was the cover overheating
The high pitch squeel was the result of a failing drum bearing. It was particularly evident when first turning on the dryer, but became softer as the dryer heated up. In order to replace the drum bearing, I removed the top panel and front door panel.

The top panel was easily taken off by removing 2-screws from the back edge of the panel, and sliding it back to release it from the front panel seam.

The front panel is more involved, but still relatively easy for your average "do-it-yourselfer". I removed the front door panel by first removing the control panel (4-screws; 2 on top and 2 from the back of the panel). I removed 2 cable assemblies from the control panel via connecters (different sizes so didn't need to mark) and 2-wires attached to the large control panel mode selector (I marked these 2-wires). I set aside the control panel. I removed the front door panel by taking off 6-screws (2 on top, 2 on the bottom, and the remaining 2 on the inside of the panel on either side of the drum). After removing these 6-screws, I carefully pulled the front door panel away from the front of the dryer, carefully releasing 4-alignment latches (2 on either side). The front door panel was still electrically attached to the machine so I had to disconnect a couple more wires. I carefully disconnected 2-wires from the door light assembly and 3 more wires from the door switch (I marked the 3-wires on the door switch). I set aside the front door panel.

From the back of the dryer, I removed the small motor access panel on the bottom left corner. This panel also provides access to the drum belt. I released the drum belt from the motor drive wheel by releasing spring tension at the tensioner. The belt can easily be disconnected from the motor drive wheel and tensioner assemblies.

Removal of the drum was now possible. With the front door panel removed, the front of the drum is maintained in place via a small plastic stop on the top crossmember. I removed this stop prior to removing the drum. With one hand, carefully grabbing the belt that is was loosely draped across the back of the drum, and the other hand holding the front lip of the drum, I provided a quick and forceful upward motion to the back of the drum in order to dislodge the drum shaft from the bearing housing assembly. Once this was accomplished, I simple pulled the drum out of the dryer housing via the front of the machine.

The drum bearing repair kit ordered came with the replacement ball bearing, bearing housing, drum shaft, high-temperature grease, and attaching hardware.

I replaced the drum shaft on the drum via the 4-screws accessed on the drum rear panel.

I removed the old bearing/bearing housing via the 2-screws holding it in place. I wasn't too concerned about loosing the small ball bearing as the kit provided me a new one. I generously applied some high-temperature grease to coat the interior lining of the new bearing housing. I also placed a dab on the back seat where the new ball bearing sits. This helped hold the bearing in place while reattaching it. I reinstalled the bearing housing to finish replacing the repair parts.

Reassembly of the drum is in the reverse order. I paid particular attention to making sure the new drum shaft properly seated with the new drum bearing housing.

After reinstalling the drum and while the front door panel was still off the dryer, it was easy to inspect the blower housing. I found the squirrel cage had broken loose from the molded nut that attaches it to the motor shaft. That would explain the heat problem; the heat was not being exhausted through the duct.

THE SQUIRREL CAGE IS REVERSE THREADED. I was unable to remove the nut from the motor shaft as the design encompasses a metal bushing molded into a plastic nut shaped form. The plastic would not hold up to the force I was applying trying to loosen the squirrel cage. So I ended up removing the entire motor and blower housing assembly from the base
Other Parts Used:
Rear Drum Bearing Kit
  • Gerald from Cumming, GA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable)
73 of 95 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blower wheel was raddling
The blower wheel was a bit difficult, but manigable to do yourself.
Other Parts Used:
  • jena from loganville, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers, Wrench (Adjustable)
22 of 48 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Motor locked
I determined the problem was the fan wheel and housing. I located the part on partsselect.com, Ordered it and installed the afternoon I got it in the mail. Perfect fit.

I have used partsselect before, always had great luck, great prices, always have the exact part.
Other Parts Used:
  • Patrick from Littleton, CO
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers
13 of 30 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
dryer after 1-3 minutes would start to buzz and vibrate - not loud nor shaking/vibrating alot but it was there
The repair actually was quite easy but diagnosing the problem was another story. I found out that the dryer would not buzz and vibrate , if I just ran the fluff cycle but no heat. As soon as heat applied, the slight buzzing and slight vibrating would occur after a few minutes. I knew it wasn't the drum bearing, the drum rollers, the rubbing collar on front of drum, idle arm, belt, etc - I had replaced all of them less than a year ago. Anything I found on the internet dealing with the motor was always geared around not running or slow starting or shutting down, loud buzzing, needing a push start to start, etc but that was not the case. So I figured it was the blower housing and ordered that part. However, once I had the machine apart the blower housing seemed to be just fine - nothing obvious, everything tight. The one issue I had was removing the plastic nut with the metal insert on the blower unit that attaches it to the motor shaft which just wouldn't bulge. So I said to myself, the h*ll with it, lets get a new motor, too and remove both parts together which btw, was very easy. So that is exactly what I did. Now with new motor in hand and new blower housing in hand, I easily removed the old motor still attached to the old blower housing together and replaced both which was very easy. Hooked everything back up and no more soft buzzing or slight vibration. Now back to the problem or my guess at this point. I noticed that the rubber mounting bushing in the back of the motor which is used to attached it to the dryer bracket was funking looking - kinda soft and a bit perished. So I am surmising that once heat was introduced, it was enough to soften that bushing enough to cause the slight buzzing and slight vibration but without the heat to soften the bushing a bit, it was quiet and steady. Just a guess but for anyone that has this issue with just heat but no issue with fluff (no heat) check out the condition of that rubber mounting bushing on the rear of the motor. No where on the internet was there any info concerning the symptoms I had and I was flying by the seat of my pants. So am taking the time to get this on record in case someone else has these symptoms and finds it.
Other Parts Used:
  • Bruce from SAG HARBOR, NY
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
9 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Vibration and Low Pitched Grinding Noise Developed as Dryer Heated Up.
**I'd already installed a new rear drum bearing assembly (very simple) and the issue continued. Further testing (running unit with the drum removed) indicated the blower assembly and/or motor was the source as the issue only occurred when the unit was under load. I ordered both parts as there was simply no way the original blower assembly was coming off the original motor.** Disconnected Power. Removed Top and Front of Dryer. Removed Drum. Disconnected Wiring Harness at Motor. Disconnected Blower Housing Temperature Sensor. Pried Open Clip Holding Motor to Mounting Bracket. Removed All Other Mounting Hardware. Removed Original Motor and Blower Assembly. Mated New Blower Housing to New Motor. Mated Assembly to Mounting Bracket. Reinstalled Clip Holding Motor to Mounting Bracket. Reconnected Wiring Harness at Motor. Reconnected Temperature Sensor to Blower Housing. Installed All Other Mounting Hardware. Reconnected Power. Checked Assembly Alignment. No Issues Noted. Disconnected Power. Reinstalled Drum and Front of Dryer. Reconnected Power. Checked Assembly Alignment While Under Load. No Issues Noted. Reinstalled Top of Dryer. Issue is Resolved. ** Thoroughly cleaned entire unit including under the baffle located at the rear of the drum. Amazing amount of baked on lint located there. Checked heating element (no issues) and cleaned lint trap assembly in door of unit. Another area with an amazing amount of baked on lint. Total for all parts needed was $236.91. Total time needed was about 3 hours. Parts arrived within one day of order. Unit operates 'as-new'.**
Other Parts Used:
Drive Motor with Pulley
  • David from PORT CLINTON, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
7 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
1. Plastic door handle was dry rotted. 2. Plastic blower 7/8 inch nut was cracked. 3. The bearings on the dryer motor where seized.
1. The old door handle was just easily pried out and the new one snapped right in place. Job took about one to 2 minutes.
2 and 3. Watched the video on how to take the blower wheel assembly and motor out and then back in. Just copied what the video showed. Really easy. It helps to have an assistant when taking out and installing the dryer drum but not mandatory.
Other Parts Used:
Door Handle Drive Motor with Pulley
  • Todd from ROSAMOND, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud persistent rubbing noise
Blower wheel came apart from molded-in nut, was loose, was rubbing on housing wall, and was likelynot moving to much air. I read some troubled stories about separating the wheel nut from the motor shaft so bought a new motor and blower housing and install wall pretty easy. There are videos on the teardown process and does that long and not alot of parts to keep track of either. I have already done the felt drum liner and rear drum ball and belt so if it's older than 15 years and your going to take the dryer apart, replace all these parts and you will about have new dryer at half the cost of new.
Other Parts Used:
  • Alan from ROCHESTER, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dryer was very noisy, like a vibration,or bad bearing
First i replaced the drum bushing on the rear of the drum ,it was definitely bad but noise was still there
Decided it was the blower assy , pulled the dryer out disconnected the power,took off the frt panel with the door, disconnected the wiring to motor remover motor and fan assy, most trouble i had was fan is on motor with reverse threads messed with removing fan until I figured out it was backwards after that removed old fan and housing installed new one ,put dryer back together,started it and only normal noises
Good for another 5 years
Chuck
Other Parts Used:
  • Charles from PITTSBURGH, PA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Screw drivers, Socket set
1 person found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
Questions and Answers

Ask our experts a question about this part and we'll get back to you as soon as possible!

6 questions answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Cindy
January 29, 2019
I took dryer apart bc making noise. The blower wheel moves freely both clockwise or counter clockwise problem seems to be it also moves forward off the shaft then rubs on the front of the assembly. Does whole thing need replaced or is there something that holds it in place?
For model number FRE5714WKO
PartSelect logo
Hello, thank you for your inquiry! More than likely, you will need to replace the blower housing with blower wheel, as we are not showing there are any separate parts listed for sale that are meant to secure the blower wheel in place. It would come as part of this assembly. Hope this helps!

8 people found this helpful.

Was this helpful?
Thank you for voting!
Bob
November 21, 2017
What does the fan blade screw onto? I mean I got threads on the end of the shaft but the bushing part on shaft has no threads.
For model number 417.84042500
PartSelect logo
Hi Bob, Thank you for the question. The Blower Wheel attaches to the shaft on the motor. Hope this helps!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Mark
February 20, 2018
Very loud vibration. I have replaced the drum bearing assembly, belt, idler arm and new oem motor. I still have a loud vibration all the time and i cannot determine where its coming from. The blower assembly is the only part left. I cannot see anything wrong, nothing is loose.
For model number GLCR341CC0
PartSelect logo
Hello Mark, thank you for your question. I would suggest removing the blower housing to see if the wheel is moving freely and that there isn't anything stuck inside the blower housing. You may also want to check the Drum Glide - White part number 137513300 as well as the Lower Front Felt Seal with Adhesive part number 5303937183. I hope this helps!

4 people found this helpful.

Was this helpful?
Thank you for voting!
Susan
December 4, 2017
Dryer blower wheel doesn't turn and motor doesn't turn either. So what is the problem, the blower wheel or the motor
For model number 41784052500
PartSelect logo
Hi Susan, Thank you for your question. Based on what you described it sounds like there is an issue with the motor and you will need to check it with a multimeter to see if it is at fault. I hope this helps. Thank you and have a great day!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Glenn
November 9, 2019
I think I need to replaced the blower housing as the dryer is making noise while running. After I opened the dryer I looked at the blower housing I noticed that it's dusty, so I cleaned it completely like it almost look like brand new but still making noise when I put it back in. My question is why do I have to replace it with a brand new one? And what is the difference?
For model number 131775600
PartSelect logo
Hello Glenn, Thank you for the question. If it is the blower making noise then the center hold where it fits tot he shaft could be worn and causing the noise. Hope this helps!

2 people found this helpful.

Was this helpful?
Thank you for voting!
Jeremy
January 21, 2019
Trying to replace blower housing you and i wood fan says to spin counterclockwise and should come off will not come off where the shaft goes through the blower wheel the centerpiece in the wheel just keeps on spinning in the wheel will not come off to be able to take the whole box off it will not release
For model number 417.98042701
PartSelect logo
Hello Jeremy, Thank you for the question. Here is a how to video on installing the blower. Hope it helps! https://www.youtube.com/watch?v=G9ecDWWp9nc

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS418726
Manufacturer Part Number: 131775600
Brand
Model Number
Description
Kenmore
41764182300
Dryer
Kenmore
41774182300
Dryer
Kenmore
41774182301
Dryer
Kenmore
41780412700
Dryer
Kenmore
41781042000
Dryer
Kenmore
41781142000
Dryer
Kenmore
41781142001
Dryer
Kenmore
41782042101
Dryer
Kenmore
41782042102
Dryer
Kenmore
41782052101
Dryer
Kenmore
41782052102
Dryer
Kenmore
41782052103
Dryer
Kenmore
41782142100
Dryer
Kenmore
41782142101
Dryer
Kenmore
41783042201
Dryer
Kenmore
41783042300
Dryer
Kenmore
41783052200
Dryer
Kenmore
41783052201
Dryer
Kenmore
41783142300
Dryer
Kenmore
41784042500
Dryer
Kenmore
41784052500
Dryer
Kenmore
41784082500
Dryer
Kenmore
41784092500
Dryer
Kenmore
41784152500
Dryer
Kenmore
41784252500
Dryer
Kenmore
41787042700
Dryer
Kenmore
41788022000
Dryer - DRYER
Kenmore
41788042700
Dryer
Kenmore
41788052700
Dryer
Kenmore
41788056700
Dryer
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service