Models > 41764182300

41764182300 Kenmore Dryer - Overview

Sections of the 41764182300

[Viewing 4 of 4]

Manuals & Care Guides for 41764182300

Click to download
Keep searches simple, eg. "belt" or "pump".
Rear Drum Bearing Kit – Part Number: 5303281153
Rear Drum Bearing Kit
★★★★★
★★★★★
(60)
PartSelect #: PS459829
Manufacturer #: 5303281153
This kit includes one bearing, one ball shaft, one ball bearing, one ball bearing retainer, a small tube of high temperature lubricant, and installation screws.
$73.24
  In Stock
Drum Belt – Part Number: 134503600
Drum Belt
★★★★★
★★★★★
(25)
PartSelect #: PS1148434
Manufacturer #: 134503600
This 88 3/4 inches long and 1/4 inch wide dryer drum belt goes around the dryer drum and the pulley to rotate the drum once the motor is activated.
$22.52
  In Stock
Heating Element Assembly – Part Number: 131553900
Heating Element Assembly
★★★★★
★★★★★
(32)
PartSelect #: PS418120
Manufacturer #: 131553900
This dryer heating and housing assembly has terminals at four o'clock. This E-line assembly comes with a felt strip and insulators already attached.
$188.46
  In Stock
Drum Support Bearing – Part Number: 131825900
Drum Support Bearing
★★★★★
★★★★★
(6)
PartSelect #: PS418807
Manufacturer #: 131825900
This part attaches onto the inside of the rear panel of the cabinet.
$7.84
  In Stock
Drum Glide - White – Part Number: 137513300
Drum Glide - White
★★★★★
★★★★★
(3)
PartSelect #: PS5574052
Manufacturer #: 137513300
Appliance requires 2 .Sold individually.
$44.79
  In Stock
Thermal Limiter - Limit 220 – Part Number: 134120900
Thermal Limiter - Limit 220
★★★★★
★★★★★
(11)
PartSelect #: PS419402
Manufacturer #: 134120900
This thermal fuse limiter, with a limit of 220 degrees Fahrenheit, is manufactured for both gas and electric clothes dryers. Once the internal temperature of the dryer reaches 220 degrees, the heating element cuts out.
$34.73
  In Stock
Door Catch – Part Number: 131658800
Door Catch
★★★★★
★★★★★
(4)
PartSelect #: PS418433
Manufacturer #: 131658800
This part helps keep the door closed while the machine is running.
$79.91
  In Stock
Lower Front Felt Seal with Adhesive – Part Number: 5303937183
Lower Front Felt Seal with Adhesive
★★★★★
★★★★★
(9)
PartSelect #: PS832645
Manufacturer #: 5303937183
$25.36
  In Stock
Lint Filter – Part Number: 131450300
Lint Filter
★★★★★
★★★★★
(4)
PartSelect #: PS417841
Manufacturer #: 131450300
This white dryer lint filter screen collects lint as it passes through the dryer vent.
$36.35
  In Stock
Front Upper Felt Seal with Adhesive – Part Number: 5303937182
Front Upper Felt Seal with Adhesive
PartSelect #: PS832644
Manufacturer #: 5303937182
The upper felt seal for your dryer is attached to the top edge of the drum support area, and is held there by a high temperature adhesive. It creates a seal where the dryer door opens and closes, so t...
$25.26
  In Stock
Door Strike – Part Number: 5303207102
Door Strike
★★★★★
★★★★★
(6)
PartSelect #: PS455020
Manufacturer #: 5303207102
"Male" piece of a dryer door closing mechanism.
$23.81
  In Stock
High Limit Thermostat – Part Number: 3204267
High Limit Thermostat
★★★★★
★★★★★
(2)
PartSelect #: PS446428
Manufacturer #: 3204267
This high limit thermostat has a limit of 260 degrees Fahrenheit. Meaning that it will cut out when the internal dryer temperature reaches 260. This thermostat cuts back in when the temperature drops ...
$118.89
  In Stock

Questions And Answers for 41764182300

Be the first to ask our experts a question about this model!

Common Symptoms of the 41764182300

[Viewing 6 of 6]
Noisy
Fixed by
these parts
Fixing Fixing Fixing
Show All
Door won’t close
Fixed by
these parts
Fixing Fixing
Show All
Marks left on clothes
Fixed by
these parts
Fixing Fixing Fixing
Show All
Too hot
Fixed by
these parts
Fixing Fixing Fixing
Show All
Drum Not Spinning
Fixed by
these parts
Fixing
Show All
Not Heating
Fixed by
these parts
Fixing
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Loud Squeaking
1. Unplug dryer from outlet
2. Using Lg. flat screwdriver, pry under the front edge of the top and release two spring tabs
3. Lift up top and tilt back out of your way
4. Unscrew two phillips scews on inside of front panel
5. Lift up and out the front panel. Two spring clips at bottom.
6. Rlease tension on drum belt at the motor. Access panel at rear of dryer.
7.Unscrew 3 screws from inside, center rear of drum.
8. Remove drum through the front of the dryer. You may have to spread the sides apart a little bit for it to fit
9. Lift up on the rear drum bearing to remove it from the bearing retainer. ( U shaped plastic socket)
10. unsrew 2 screws and remove the bearing retainer, ground ball. Ball retainer is on outside of dryer.
11. Vacuum everything--duct, blower, lint trap, ect.
12. Intall new bearing retainer and grounding ball, an assistant is helpful at this time, one to hold ball retainer on rear of dryer, one to screw it in from the inside
13. reassemble remainder of parts in reverse order.
Parts Used:
Rear Drum Bearing Kit
  • Frank from Boyertown, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver, Screw drivers
333 of 349 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
short circuit with a brasier metal support
Disconect the dryer from the main power source.

1) Remove the two screws from the rear / upper panel (below the control panel).

2) Snap the front side using a flat head screw driver.

3) On the inside front, remove two screws (one on each side) from the upper side and snap the door assembly off.

4) Remove the rear motor access panel (two screws) and appying tension to the spring remove the belt.

5) Pull the drum upwards (verticaly) unnapping it from the rear wall and remove it horizontally through the front panel.

6) Disconect the four leads to the heating element and remove the four screws from the rear of the dryer and replace the heating element.

Follow the same steps backwards to put the dryer together again.
Parts Used:
Heating Element Assembly
  • Juan Carlos from Weston, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
233 of 271 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Thermal Limiter opened
Unplugged Dryer.
Opened top of Dryer, over the drum.
Removed Thermal Limiter.
Tested the Thermal Limiter - found it was open.
Checked all vents and exhaust tube for lint build-up.
Replaced Thermal Limiter.
Closed top of dryer.
Plugged Dryer back.
Tested Dryer - it works.
Parts Used:
Thermal Limiter - Limit 220
  • Stephen from Newnan, GA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
241 of 317 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!