This part is located behind the control panel. It helps determine the level of water in the washer. As the water fills the hose, while tub is filling, it will push the air against a diaphragm inside the switch. More water that enters the tub, more pressure is applied against the switch.
How Buying OEM Parts Can Save You Time and Money
Part Videos
Replacing your Kenmore Washer Water Level Switch
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Kenmore, Whirlpool, KitchenAid, Crosley.
Part# W10339326 replaces these:
AP4568366, 1658886, 3366845, 3950420, W10339326VP
Customer Repair Stories
Average Repair Rating: 3.8 / 5.0, 6 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Water in washer would continue to fill and overflow
Read on Internet to diagnose and get at part. Luckly they sent new fill hose along with level control switch as that was problem. Visually there was no kink or blockage. Upon removing hose, I discovered a slit on hose which did not allow pressure to actuate diaphram. I installed new switch and never thought to return as savings instead of calling repairman was a no brainer !!! Word of caution " never force"when removing or installing a part. It should be easy Steve, Ca.
Other Parts Used:
Steve K. H. Chun from Redwood City, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
22 of 26 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water Level Switch Broken
The repair is very easy with the part found at PartSelect.com. Take the following steps to replace the water level switch: 1. Remove the front panel by unscrewing two screws on the back side 2. Pull off the dial knob from the front 3. Twist the water level switch in either way to remove the switch from the panel 4. Disconnect the connector of control wires and water hose from the broken switch 5. Reconnect the control connector and water hose 6. Push and twist the switch to put back on the front panel 7. secure the front panel by tighten up two screws on the back side of panel
Other Parts Used:
Bo from Sugar Land, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
11 of 14 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Water overflow when set at Ex-Lge load
After moving washer and UN-Plugging electrical. 1. Remove the 2 screws that hold the Control Panel to the lower chassis. 2. Lift the Control Panel up and forward to expose the water level switch. 3. Remove the dial. 4. Remove the old switch, (a plastic tab locks it into the panel, try to release it(from the front) with a small screwdriver, (mine broke off, releasing the switch). 5. Remove the electrical connection by lifting the connection locking tab. 6. Remove the air tube. 7. BLOW into the air tube to ensure it is not blocked. 8 . Reconnect the air tube and electrical connection. 9. Carefully install the new switch into place, turning it to line up and lock the tab into the panel. 10. Re-install the dial and return the Control Panel screws into the lower chassis. NOTE: If the included air hose needs to be replaced, the time and difficulty needed to make repairs will increase.
Couldn’t adjust water level. Knob was the problem.
The part I ordered was not needed, however, I was issued a credit on the returned part in a very prompt manner. I would not hesitate ordering parts I might need in the future.
Other Parts Used:
Lloyd from BENSALEM, PA
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
over filled with water
remove two screws in the control panel,slide it ahead ,tipped it back,removed the knob from switch,turned 1/2 turn and it came out.unplugged the wireing and hose.installed new switch,seems to work fine.i ordered the coupling but did not use it yet,with the age of the washer i expect it to fail soon.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
7 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
JASON
December 3, 2017
I broke the blue stem in the water level switch. Is just the blue stem available?
For model number LSQ9549PW2
Hi Jason,
Thank you for your question. The blue stem or shaft is not sold separately and is sold with the switch. I hope this helps. Thank you and have a great day!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Robin
November 3, 2017
My washer will not stop filling with water on rinse cycle even if the washer is turned off. It stopped filling on the wash cycle, went through the cycle, and started filling for rinse cycle and would not stop filling. I am not sure which part I need. Can you help?
For model number LSQ9549PW1
Hello Robin,
Thanks for your question. Based on your inquiry, you will want to look at your water inlet valve and thermistor assembly, part number PS11742194. Test it for continuity with a multi-meter and check for any cracks in its base. The part number PS3408155, which is the water level pressure switch, should also be tested for continuity to ensure it is functioning properly. Lastly, examine the water pressure hose, part number PS11741846, to check for any debris and to see if it is leaking.
We hope this helps.
The original water valve
I replaced the water valve with with a Generic hot and cold only water valve
Now water water will not stop
If i turn the machine off or if i unplug the washer the water stops flowing
I have tested the water level switch and checked hose and all seams good
Any help would be appreciated
Mike
For model number 11022996100
Hello Mike, thank you for your question. If the water stops flowing when the unit is unplugged the valve is not bad. It sounds like the valve is not compatible with your unit. We would recommend replacing the valve with PartSelect Number PS11746094. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Hanna
April 11, 2019
My washer is not filling with water. It spins and agitates fine. I replaced the water inlet valve and it still does not fill.
For model number GST9679PWQ
Hello Hanna, thank you for inquiring. For this symptom, besides the Water Inlet Valve and Thermistor Assembly, you will want to replace either the Direct Drive Water Pump part PS11741239, the Water Level Switch part PS3408155, or the Direct Drive Motor Coupling part PS1485646. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Paul
August 12, 2022
My washer only fills slowly in the rinse cycle. I just replaced the hot/cold fill valve. But the problem still occurs. Could it be the pressure switch or water level switch?
For model number 110.22956 102
Hello Paul, Thank you for your inquiry. It could be either the water level switch, or the water pressure hose. Check the hose for any visible damage, and you can test the switch with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps and if you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Washer over flows water on the permanent press cycle only, all other cycles work fine.
For model number 11020722990
Hello Robert,
Thank you for your question. Our sources suggest replacing the water level switch for your model under part PS3408155 to fix the water overflowing issues. We hope this helps
Was this helpful?
Thank you for voting!
Jeremy
July 31, 2021
Whirlpool washer giving code f27 any help would be greatly appreciated
Hello Jeremy, Thank you for the question. The F27 error is displayed when there is too much water and/or suds in the washer. It's an overflow condition which means the water pressure switch has too much pressure on it causing the overflow contacts to close and will show Failure. If you provide the model number, we can search out the correct part number for you. We hope this helps.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
