Triple Lip Seal and Bearing Kit W10116791

Spin cycle sounded like freight train, bad bearing, apparently they all fail the same way, this revised parts kit should prevent premature failure in future.

The following is easy for an experienced mechanic of any type, fully doable by an accomplished DYI'er, between this writeup and the kit instructions (which I do not fully follow) you should be fine. Probably avoid this task if you aren't either of the aforementioned.

Remove lower pannel, top pannel, lift top back. Remove fill hose to outer tub, clear tube to outer tub. Remove entire outer cabinet from base, exposing base and tub. Remove augur assy by popping off cap removing inner bolt, lifting augur out. Remove top of outer tub cap assy by pressing down where each latch is and gently prying latch open with screwdriver. Remove bolts holding in inner tub and remove inner tub. Unscrew the pastic nut on transmission shaft using channel locks (counterclockwise from top), don't worry about destroying this part since a new one is in the kit. Remove (pry off with your hands, don't worry about breaking it) the 'lint filter' (looks like a frisbee) and trash it. Remove the large (about 8")aluminum hub (that the inner tub bolts to) by unscrewing counterclockwise. No special tool needed, just use air hammer if available against one of the T shaped castings to get it loose, otherwise use a drift and hammer same way. Don't worry about messing up the part since a new one is in the kit. Remove the outer tub drain hose, remove six screws holding outer tub, lift outer tub out. Turn outer tub upside down and use a wide crowbar/nail puller to CAREFULLY pry out the bearing/seal assy from the bottom of the tub. Take your time working your way completely around the bearing/seal several times so it doesn't get too crooked while removing it. Clean everything thoroughly. Inspect the area of the bottom of outer tub where you removed the bearing/seal. If all is well and there are no gouges, get it wet with clean water and then carefully press the new bearing/seal assy in with the heal of the palm of your hand, working your way around it so it doesn't get crooked while pressing in. Do not use sealer (unless there are gouges) and do not hammer this. Make sure it is fully seated in the outer tub. Do reverse to put everything back together. I tightened the aluminum hub the same way I loosened it, no problem. There are some rubber plugs in the kit to install in some holes in the tub, scrape or clean any gunk off the inner tub around these holes so the rubber plugs will seat properly. Carefully snug the plastic nut with channelocks by gripping it from the top as opposed to the side (so the fins don't break). Note there is a small o-ring on the transmission shaft to change before replacing the augur. Nice and quiet after the repair, hopefully the new kit (and trashing the 'lint filter') makes it last longer... LOL, it's a bit disturbing seeing the gunk under the augur knowing that has been there all this time while 'cleaning' the laundry! I'll probably start removing the augur every so often to clean under there.

1. I unplugged the machine. Using a socket wrench set, I removed the washer housing (bottom, front and sides) and flipped over the top to its service position. This exposes all the inner parts of the washer.
2. I pulled out the softener cup, unbolted the auger using a socket wrench with a long adaptor. I then pulled out the auger, exposing the "Seal Nut" and bottom of the inner basket (metal)where the transmission arm rises through.
3. I removed the seal nut using the hub (or spanner) wrench, which I had purchased from the Home Depot for $9.00;
and removed the bolts of the inner basket using a socket wrench. I unclipped the large plastic ring which holds together the inner metal basket and the outer plastic tub. This ring sits on top of both. I then removed all the counter-balance springs attached around the tub assembly.
4. I pulled out the inner basket exposing a metal disc called the "hub", which holds the inner tub in place.
5. Using a large flat screwdriver and a hammer, I tapped on the "T" shaped protrusions around the hub to loosen the hub, as it is tightly screwed onto the tub. Remember that the hub is "uncrewed" counter-clockwise. I didn't take much care in tapping the hub because I knew that this part will be replaced.
5. I then unscrewed the hub using the hub wrench.
6. I carefully pulled out the inner tub throught the transmission arm.
7. I inverted the tub, placing it on a towel on the floor (I didn't want to crack the lip). Using a flat screwdriver (or a nail puller), I slowly pried out the triple lip seal and bearing (the metal ring in the center of the tub bottom), making sure that I DO NOT DAMAGE THE PLASTIC BOTTOM OF THE TUB where the bearing sits. At this point, I pushed out all the little plastic lint strainers around the bottom of the tub (as per the instruction leaflet) and replaced them with the provided rubber plugs. YOU WILL HAVE TO MAKE SURE THAT THE PLUGS ARE FIRMLY IN PLACE.
8. I now washed the auger (you will find residue/softener build up inside), the inner basket, and the outer tub. I also found dirt, sand, grime and mold in these parts and cleaned them thoroughly. This got rid of that smelly odor that my washer had for quite a while now.
9. I checked and saw water on the transmission disc where the lower bearing is. I figured that the lower bearing needed replacement as well.
10. I removed the lower transmission by removing the blots on the motor, and undid the belt from the pulley and gear.
11. While I had the brake pads exposed, I also applied a touch of automotive brake cleaner and brake spray.
11. I replaced the lower bearing with the new part, reattached the transmission ( I replaced the small "o-ring" on the transmission arm) and the motor and belt.
12. I replaced the tub seal bearing following the instructions provided with the new part.
13. I put the tub back, screwed on the new hub using the hub wrench, then CAREFULLY gave a couple of taps with my hammer and falthead screwdriver to tighten it. I placed a new gasket on the hub, screwed on the new seal nut, then repositioned the inner basket on.
14. After re-installing the tub and the inner basket, I put back the plastic ring that holds both tub and basket. I re-installed the auger and the cup.
I ran the machine for a test before I put the housing back in place to check for any leaks. THERE WERE NO MORE LEAKS, AND THE MACHINE SOUNDED AS GREAT AS IT DID WHEN WE PURCHASED IT 5+ YEARS AGO!

First removed the front panels and tilted the top back.Disconnected the electrical connector to the motor,removed the cabinet base screws and slid the entire cabinet away from the interior after disconnecting the clear tube and the water feed to the panel.removed bolt inside agitator and remove agitator.removed the plastic hold down center nut with channel lock pliers.remove top cover from outer tub(pry out over tabs with screw driver).remove 4 bolts holding inner tub and remove tub.remove inner bottom tub support with pliers(screws off).remove 6 machine screws from frame to bottom of plastic outer tub and remove tub.Carefully pry seal/bearing out of tub from the bottom(remember its just plastic).install is just the reverse of the dissassembly.Note: This is the second seal/bearing for this washing machine in less than 2 yrs..I work in the Site developement/construction field and my clothes get extremely dirty.The dirt is being held under the inner tub support and driven down thru the seals and into the bearing(great design).This go around the intsructions called for the removal of the plastic lint filter under the tub support which I believe was a large part of the problem.I hope so.I'm not going to spend $90 every 2 yrs. on this machine.Good luck.

Amana top load laundry machine
Model # NAV2230AWW
Parts used: PS2040734 and PS2177502

NOTE: the hub seal kit comes with the gasket foam and hub nut so do not order them separately as I did. PartSelect is great about accepting returns, but you might as well know ahead of time.

When you are starting this project out, there are a few things you should be prepared with. First, you will need an extension for your ratchet so that you can get at the bolt in the center of the agitator. Second, make sure you have some sealant or grease on hand for the installation of the hub nut.

Actual dis-assembly of the washer is not difficult. Simply remove the lower front panel followed by the main front panel and then separate the outer shell. Once all these parts are removed you can remove the agitator and all the various tub parts. The instructions that come with the kit are detailed enough to easily walk you through this part.

If you have diagnosed that the upper bearing/seal is the issue you will want to check the lower one as well. In my case the failure of the upper bearing resulted in a leak which caused the lower bearing to fail as well. Once you get to actual removal of the bearings you will be well served to have a bearing removal tool. If you do not have one, getting the lower bearing out will be quite difficult. If you have one, pulling the bearing out and replacing it is quite simple. Reassembly is even easier.

Plan on this repair taking several hours. It took me about six hours but that was due to the fact that I spent a lot of time cleaning each part thoroughly before reassembling the unit. I figured that since I had it all opened up I might as well. Had I not done this I think I could have gotten the whole thing done in about three hours.

After the repair the “jet engine” noise that was present during the spin cycle is gone and there is no leak. Given the cost of having a service person come to the house and make this repair I would definitely recommend that you do it yourself. PartSelect made this really easy. This is the third repair I have made to appliances using PartSelect and I have been fully satisfied with the parts and service each time.

James Erickson
Saint Paul, MN

Following on-line instructions for the dis-assembly. Replaced bearing and seals for outer drum bearing and cleaned and lubed assembly.

Not only very loud at spin cycle, but started to leak water as well. Pulled lower front panel off and ran a load of clothes while laying on the floor with flashlight watching. Sure enough, water spraying out from outer tub bearing area.
Remove top front panel, sides and top, disconnect hoses and unplug wires at top of control panel, there is a plug in there. Now you should just have base unit and tub exposed so you have plenty of room to work. Next joy is to remove agitator. This is where my fun began. After removing fabric softner dispenser from top of agitator, I could not see bolt holding it on. There was a long plastic rod sticking up which looked like part of the agitator itself, so went online to a repairmans site and they said simply pull that rod out and bolt will be under it. Paid 24 bucks to them and still could not remove rod, ended up going thru slots in side of agitator with a small chisel and cutting it off, then took a 3/4" hole saw and drilled hole in top of agitator, its only about 1/8" thick and what do you know, THERE is the bolt!!!!!!! Removed bolt and out comes agitator. Next, remove cap from outer tub, take 4 bolts out of inner tub, remove inner tub. Next, remove plastic nut from shaft, I tried this with channelocks and could not budge it, ended up splitting nut with chisel and slightly damaged threads on shaft which I cleaned up easily with 60 degree thread file. Be very careful if you use this method. You can use channelocks to reinstall, just clamp on the unfinned part of nut.Take out the lint filter and throw in garbage, do not reinstall!!!!!! That filter is part of the reason tub bearing goes out!! Next, remove aluminum hub from shaft, mine was already loose so was easy. If yours is tight, screw in one of the old inner tub bolts almost all the way in and use hammer and punch to loosen. You can do the same for new one. Next, remove 6 bolts from outer tub and pull outer tub off shaft.Flip outer tub upside down and gently pry bearing out, mine came out easy as was spinning inside tub bearing fit. After cleaning everything I used Scotchseal 800 industrial sealant because bearing fit was loose. I made a clamp out of 1x2 wood and a long 1/4" bolt to hold bearing in tub to prevent it from pushing out, sometimes the sealant will cause this to happen, then I let it setup for 24 hours. Put it all back together, no leaks and SUPER quiet. Be sure and check your bottom bearing too while you have it all torn down, mine was fine. Do not forget to change O ring on spline shaft before reinstalling agitator. As far as the hole I drilled in agitator, just tapped it 1/2" pipe and screwed in a plastic pipe plug. You will need an extension and a 5/8" 12 point socket to do this.

Unplug and disconnect Power, Drain and h20 connections. Removed front panel, disconnected internal electricrical connections and capicitor from washer. Remove 11 (I think) screws connecting outer cover to base. Remove pull drain hose through the outer cover and hold the end lower that the washer to drain the excess h20. Remove the hoses from the pump and outer tub. Remove outer cover from base exposing the guts. Grab the bottom of the agitator and pull up pretty hard. Agitator will pop off, watch your head. Remove the 4 bolts attaching the Inner tub to the hub. Remove seal from top of transmission spline. You will need a 38mm deep well socket to remove the nut from the top of the transmission. I used a socket and a impact wrench to remove the nut. Remove the teflon seal that is below the nut. You will need a puller and/or grinder to remove the hub from the transmission spline. My puller broke, so I ended up using an air grinder to cut a couple of pizza slices out of the hub. Then I used an air hammer to break the slices off of the hub. Once it is cut the cast aluminum is quite brittle. Pull what remains of the hub off of the transmission spline. Remove the bolts that connect the transmission housing to the outer tub. Remove the 3 bolts from the underside of the outer tub that connect the outer tub to the upper bearing. using a set of vice grips, grab the top of the springs that connect the outer tub to the base and carefully remove them one by one.
The outer tub should slide right off. Remove the bearing from the transmission. Supplies that you will most likely need are the 3m800 sealant, when you get this you will only need a little around the bottom of the lip where the new seal attaches to the bottom of the outer tub. You will also want to get the Seal tool which will ensure that the seal that goes around the top of the transmission spline is seated properly. Assemble in reverse order but keep in mind to attach tub bolts prior to attaching the springs. Also keep in mind that both maytag and amana make a washer with the same model number LWA80AW. Check to see which one you are ordering for. The kits are different. Don't ask me how I know. Just make sure you get the correct kit the first time, it will save you a whole lot of head scratching.

I removed the lower front panel to diagnose the problem. After finding this, it would have been best to purchase the parts because the instructions on how to disassemble the unit came with the parts. Sad to say, I didn't tighten the main hub, at the bottom of the unit, good enough because it came loose and I had to go back and do a better job. Luckily I was able to fabricate the tool to tighten it better. Too bad the web page didn't recommend the right tools for the job. I would have purchased them.
All in all the job went well. I am pleased with the parts and prints available to complete the job. I could have used some instructions before removal of the parts, but where would be the adventure in that, right?

Rivman,
Milwaukee, WI.
12/2009

After totally disassembling the washer ; the parts arrived, wrong parts! called and resolved issue, recvd parts and proceeded without special tools, PB Blaster solvent is awesome!!! I removed the seal & bearing with little effort with a hammer and screw driver. Greased new seal and installed effortless. Waher back in operation in less than 2 hours of receiving the parts.

I read what the others had done and thought it was the lower bearing so I originally tore it down and replaced just the lower bearing.

Unfortunately, after 2 + hours of doing that and putting it back together, it still didn't fix the problem. So I read more reviews and others claimed to use this kit and that it fixed the problem. So I ordered the kit.

BTW, Parts Select rocks!!!! They get me the part within about 2 days every time.. Great Service! Thanks guys!

Anyhow, part came in, knowing how to tear this thing down now, I was able to get to where I needed to be within about 45 minutes.

2 things that were difficult.

The first was removing the plate at the bottom of the tub. This is the aluminum plate that looks somewhat like a spoked wheel. Maytag has a tool for this. Without it, you must go at it with a small punch on one of the spokes and carefully tap the seal until it turns. You may have to try it from different angles to loosen it up but it will eventually give way..

Once you get that off, the second little piece of joy is actually removing the seal from the bottom of the tub. Here again, Maytag offers a tool to remove this. Without it, and with years of this rubberized fitting mounted in this plastic tub and corrded with water and crap... you will need to create a bearing puller.

I did so with a 2X4 board straddled across the bottom of the tub. I used an 8 inch lag bolt, drilled a hole through the 2X4 and placed the lag bolt throuigh the board and through the center of the bearing. I attached a large washer and nut to the bottom side of the bearing and then began to tighten the bolt on the other side of the board. By tightening the bolt, the board created alot of tension but not enough still to seperate it from the tub. With the tension on the bearing, I turned the tub over and tapped it with piece of wood the size of the bearing and a rubber mallet. It popped right off. The rest was just reassembly.

Don't forget to remove the sticker backing on the felt gasket to hold the gasket in place while you screw the tub back together...

The good news... Super quiet! So, about 3 hours.... (I had to come up with the idea to remove the bearing and build it) and it's all done..

Yeah.... Fun Saturday.