Part Location Diagram of WP27001006 Whirlpool V-Style Spin and Agitate Belt - 28-3/4 inches long
See part 22 in the diagram
( Grid squares measure 1x1 inch )
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

customerservice@partselect.ca

V-Style Spin and Agitate Belt - 28-3/4 inches long

$85.46
  In Stock
PartSelect Number PS11740577
Manufacturer Part Number WP27001006
Manufactured by Whirlpool
Product Description

V-Style Spin and Agitate Belt - 28-3/4 inches long Specifications

This v-style spin and agitate belt is 28-3/4 inches long and half of an inch wide. It is all black in color and made entirely of rubber.
How Buying OEM Parts Can Save You Time and Money

How Buying OEM Parts Can Save You Time and Money

Troubleshooting
This part fixes the following symptoms:
Burning smell | Will not agitate | Will not drain | Spins slowly
This part works with the following products:
Washer.
This part works with the following products:
Speed Queen, Amana, Maytag, Crosley.
Part# WP27001006 replaces these:
AP6007462, 2200063, 27001006, 38174, 40053601, 40053606, WP27001006VP
Back to Top
Customer Repair Stories
 Average Repair Rating: 2.3 / 5.0, 12 reviews. What's this?
  • 1
  • 2
Sort by:
Sorry, we couldn't find any existing installation instruction that matched.
unusually loud rumbling in spin mode, no spin out
removed outer enclosure to expose inside workings. removed all retaining springs to tub and transmission housing. Inverted tub to access agitator pulley and belt. Removed pulley and cut belt off.(I knew I was replacing it, anyway.)Had to remove large tub bracket to exchange new pulley for old. Disconnect bleach reservoir filler tubing on tub assembly. Disconnect power connector to drive motor. Removed water pump to access drive pulley where new belt belongs. Aligned belt to pulleys and checked idler pulley tension which was acceptable. Replace helix drive lug against spin/agitator and tightened retaining bolt. Assembled components in reverse order and conducted test run. Success. Smooth running machine and saved about $200 on professional labor costs. I had no repair manual but you should have a personal confidence in general repair work. Something like a history of taking things apart and putting them back together successfully. I had an independent appliance repair guy examine the washer and he said it was too complicated for him. Once I had it apart, it seemed fairly basic. Good luck!
Other Parts Used:
Plastic Helix Drive Lug Agitator Pulley Spring Retaining Clip
  • Ralph from Moreno Valley, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
37 of 45 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bad shaking During Spin Cycle
firsted layed washer back On A Angle For Easy Acess To Motor Removed Both Hoses And Four bolts pulled Motor Assembly out replced belt @ idler Pulley Reinstalled Motor.
Other Parts Used:
Idler Pulley Wheel
  • Gary from Park Ridge, IL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers, Wrench set
35 of 53 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Idler pully seperated from bushing
first I unplugged the electrical plug then I removed the lower covet by taking out the 5/16 screws. I then took out the 5/16 screws that hold the top part of the front cover and removed it.
I then worked the belt off the aggitator pully and removed the hoses from the pump. I then used a 1/2 in soclet on long extension th remove the four bolts that hold the motor and pump assembly. I then worked the assembly out of the cabinate and using a long #20 torx bit I removed the pumfrom the housing. I removed the belt, then I removed the housing off the motor and replaced the Idler bracket with the idler pully. I then re-assembled it in the reverse of taking it apart. Works great with the new idler and belt.
David Hilton
Other Parts Used:
Idler Lever Thrust Washer Idler Pulley Wheel Retaining Ring
  • David from Raytown, MO
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Socket set
14 of 17 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Squeak and slight burning smell during spin cycle.
I took off the lower front panel and “watched” with a flashlight during the spin cycle. I could see that the idler pulley was intermittently stopping and starting. The back of the drive belt was also worn in the center. When the idler pulley was moving, it squeaked, when it didn’t, the friction wore the belt and made the smell.

To replace the Idler Pulley Wheel:
1. Take off the lower and upper front panels to access the motor assembly.
2. Remove motor by loosening four bolts.
3. Remove spring that applies tension to the idler pulley.
4. Remove the electrical connector by squeezing the plastic tab on top.
5. Remove hoses by gripping clamps with pliers (put down rags first to catch water)
6. Unhook belt from tub pulley
7. Remove 1 cabinet spring to make it easier to remove motor
8. Remove motor.
9. Remove allen screws holding the pump to the motor
10. Remove the pump and belt (take note of the location of the belt before removing).
11. Remove retaining ring to replace Idler Pulley Wheel (this was probably the trickiest part; I used a very tiny needle nose pliers and straight screwdriver).
12. Replace the washers on either side of the Idler Pulley Wheel as well as the retaining ring.
13. Replace belt.
14. Reassemble in reverse order.
15. Be thankful for the money you saved on a service call.
Other Parts Used:
Idler Pulley Wheel Retaining Ring Thrust Washer
  • Jim from Swanton, OH
  • Difficulty Level:
    Easy
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set
13 of 15 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
broken belt and the pump was damaged/stripped
To replace the pump and belt for the Maytag washer, you really need remove the springs and suspended the tubs. I needed help to pull the 2 springs out (high tension) with a big plier. I removed the 3 bolts that held the motor to the frame and flipped it out to the side to expose the 3 long screws that attached the pump to the motor. The pump was easily removed and replaced with the Philip screw driver. I preset the belt between the pump and the rotor before sliding the motor back in place. After botling the motor back into the frame and carefully pull and snap the spring back into the holes, I routed the belt around the pulley and turned it into the groove. This took some time to get it on properly as it is pretty tight. Once the cover was replaced, the washer worked as expected.
Other Parts Used:
Drain Pump
  • Anh from San Jose, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Screw drivers
10 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old belt burned up
1) removed front panels from washing machine
2) removed water pump. Three small torque bit screws and (2) hoses.
3) removed motor (because I realized that the belt tensioner also needed work as it was siezed) removed (4) bolts and an electical connector.
4) repaired tensioner by taking apart and cleaning bearing surface. Needed snap ring plyers to take apart.
5) put motor back in
6) replaced belt
7) put water pump back on
8) intalled front panels back on washer
Other Parts Used:
  • TOM from MERIDEN, CT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Pliers, Socket set
6 of 11 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Sweaking and then Burning
I had some sweaking and then burning followed. I came to find the belt had burnt and stopped my washer from working. Ordered a belt and replaced. Washer worked for one week. Squeaking and burning again. Belt was still intact, thank goodness. Beleive it is another pulley part for the washer. Might order another part. Overall the fix was good, but had another issue.
Other Parts Used:
  • Kristine from Montgomery, PA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer doesn't drain water during spin cycle
Thanks for very quick delivery and detailed instructions found on this site. I followed the step-by-step instructions and everything went as planned with one exception, I installed the V-belt in a wrong way after replacing the pump. Next time, I will mark or remember the way belt sits between the motor and the pump.
I found a small sock in the pump. Pump itself was still good (I think), but I installed new one along with new belt (just in case).
Other Parts Used:
Drain Pump
  • Artur from Burlington, CT
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Pliers, Screw drivers, Socket set
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Belt degraded with failure
After turning on the machine set to the spin cycle and acertaining that the problem was not a switch or the motor the lower cover was removed (Two sheet metal hex head screws)with appropriate socket. The failure of the belt was self-evident, having sprayed itself in granuals, the belt itself having parted with easy removal.
A search of the internet produced the order for drive belt, which arrived in a timely manner trough Fedex.

Replacing the belt was the most labor intensive part of the process. No mirror being available a CD was placed in the base of the machine in order to view what fasteners (Three torx head) fasened the pump to the motor assembly. Removal of the pump was necessary in order to replace the belt.

The removal of the fasteners required that three holes (120* angular spacing, 1/2" diameter, located on the pump fastener bosses) be drilled in the machine base in order to
remove and replace. This required setting the machine on its side. (Tell the engineers to put an inspection plate there in order to negate having to drill the holes. Thankx.) Pump assembly was lowered off driveshaft and belt replaced. Tensioner set on belt after pump assembly fit to driveshaft and torx fasteners replaced and tightened. Machine powered up, checked for function. In use. Lower cover replaced. I'll be using your buisness for parts again, no doubt.
Other Parts Used:
  • Henry from Bradenton, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Nutdriver, Wrench set
4 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Upper Bearing sounded like jet taking off during spin cycle, burnt belt in half
Unplug and disconnect Power, Drain and h20 connections. Removed front panel, disconnected internal electricrical connections and capicitor from washer. Remove 11 (I think) screws connecting outer cover to base. Remove pull drain hose through the outer cover and hold the end lower that the washer to drain the excess h20. Remove the hoses from the pump and outer tub. Remove outer cover from base exposing the guts. Grab the bottom of the agitator and pull up pretty hard. Agitator will pop off, watch your head. Remove the 4 bolts attaching the Inner tub to the hub. Remove seal from top of transmission spline. You will need a 38mm deep well socket to remove the nut from the top of the transmission. I used a socket and a impact wrench to remove the nut. Remove the teflon seal that is below the nut. You will need a puller and/or grinder to remove the hub from the transmission spline. My puller broke, so I ended up using an air grinder to cut a couple of pizza slices out of the hub. Then I used an air hammer to break the slices off of the hub. Once it is cut the cast aluminum is quite brittle. Pull what remains of the hub off of the transmission spline. Remove the bolts that connect the transmission housing to the outer tub. Remove the 3 bolts from the underside of the outer tub that connect the outer tub to the upper bearing. using a set of vice grips, grab the top of the springs that connect the outer tub to the base and carefully remove them one by one.
The outer tub should slide right off. Remove the bearing from the transmission. Supplies that you will most likely need are the 3m800 sealant, when you get this you will only need a little around the bottom of the lip where the new seal attaches to the bottom of the outer tub. You will also want to get the Seal tool which will ensure that the seal that goes around the top of the transmission spline is seated properly. Assemble in reverse order but keep in mind to attach tub bolts prior to attaching the springs. Also keep in mind that both maytag and amana make a washer with the same model number LWA80AW. Check to see which one you are ordering for. The kits are different. Don't ask me how I know. Just make sure you get the correct kit the first time, it will save you a whole lot of head scratching.
Other Parts Used:
Triple Lip Seal and Bearing Kit
  • Tracy from martinez, GA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
4 of 10 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
  • 1
  • 2
Questions and Answers

We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.

1 question answered by our experts.
  • 1
Sort by:
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Brian
February 18, 2018
Hi planning to replace the belt and idler pulley on my Maytag washer (model sav515deww). The belt on the machine right now has the following part number stamped on it: 2200063. This is not listed as one of the belts replaced by partselect number ps11740577 / manufacturer part number wp27001006, so i'm seeking confirmation this is the right replacement belt for this machine model. Also want to confirm that this is the right idler pulley for this model machine: Partselect number ps11742250 / manufacturer part number wp40045001. Both have the check mark that they work with this model, but i previously bumped into a slight difference for another part based on serial number. Thanks!
For model number SAV515DEWW
PartSelect logo
Hi Brian, Thank you for your question. The part number listed under your model number for the belt is PS11740577. I hope this helps. Thank you and have a great day!

2 people found this helpful.

Was this helpful?
Thank you for voting!
  • 1
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS11740577
Manufacturer Part Number: WP27001006
Brand
Model Number
Description
Amana
ALW110RAW-PALW110RAW
Washer - Amana Washing Machine Model ALW110RAW-PALW110RAW (ALW110RAWPALW110RAW, ALW110RAW PALW110RAW) Parts
Amana
ALW210RAW-PALW210RAW
Washer - Amana Washing Machine Model ALW210RAW-PALW210RAW (ALW210RAWPALW210RAW, ALW210RAW PALW210RAW) Parts
Amana
ALW210RMC
Washer - Residential
Amana
ALW210RMW
Washer
Amana
ALW430RAC-PALW430RAC
Washer - Amana Washing Machine Model ALW430RAC-PALW430RAC (ALW430RACPALW430RAC, ALW430RAC PALW430RAC) Parts
Amana
ALW430RAW-PALW430RAW
Washer - Amana Washing Machine Model ALW430RAW-PALW430RAW (ALW430RAWPALW430RAW, ALW430RAW PALW430RAW) Parts
Amana
ALW450QAW-PALW450QAW
Washer - Amana Washing Machine Model ALW450QAW-PALW450QAW (ALW450QAWPALW450QAW, ALW450QAW PALW450QAW) Parts
Amana
ALW480DAC-PALW480DAC
Washer - Amana Washing Machine Model ALW480DAC-PALW480DAC (ALW480DACPALW480DAC, ALW480DAC PALW480DAC) Parts
Amana
ALW480DAW-PALW480DAW
Washer - Amana Washing Machine Model ALW480DAW-PALW480DAW (ALW480DAWPALW480DAW, ALW480DAW PALW480DAW) Parts
Amana
ALW540RMC
Washer - Residential
Amana
ALW540RMW
Washer - Residential
Amana
ALW780QAC-PALW780QAC
Washer - Amana Washing Machine Model ALW780QAC-PALW780QAC (ALW780QACPALW780QAC, ALW780QAC PALW780QAC) Parts
Amana
ALW780QAW-PALW780QAW
Washer - Amana Washing Machine Model ALW780QAW-PALW780QAW (ALW780QAWPALW780QAW, ALW780QAW PALW780QAW) Parts
Amana
ALW780QMC
Washer
Amana
ALW780QMW
Washer
Amana
ALW880QAC
Washer - Residential
Amana
ALW880QAC-PALW880QAC
Washer - Amana Washing Machine Model ALW880QAC-PALW880QAC (ALW880QACPALW880QAC, ALW880QAC PALW880QAC) Parts
Amana
ALW880QAC1
Washer - Top Loading
Amana
ALW880QAW
Washer - Residential
Amana
ALW880QAW-PALW880QAW
Washer - Amana Washing Machine Model ALW880QAW-PALW880QAW (ALW880QAWPALW880QAW, ALW880QAW PALW880QAW) Parts
Amana
ALW880QAW1
Washer - Top Loading
Amana
ALW891SAW
Washer - Top Loading
Amana
ALW895SAC
Washer - Residential
Amana
ALW895SAW
Washer - Residential
Amana
ALW990EAC
Washer - Top Loading
Amana
ALW990EAW
Washer
Speed Queen
AWN311SP111TW01
Washer - Speed Queen Washing Machine Model AWN311SP111TW01 Parts
Speed Queen
AWN402PP111TW01
Washer - Speed Queen Washing Machine Awn402pp111tw01
Speed Queen
AWN412
Washer - Speed Queen Washing Machine Model AWN412 Parts
Speed Queen
AWN432SP113TW01
Washer - Speed Queen Washing Machine Awn432sp113tw01
Customer Service Representative

Get in touch, we're here to help!

Monday to Saturday
8am - 9pm EST

Contact Customer Service