Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
ALEX L - January 19, 2023
Verified Purchase
Simple to change the part
Remove a little hex screw. Feel it with your fingers and use an appropriate ratchet. Slide the defective part up and out. Reverse the installation with the new part. Make sure to torque the screw otherwise to the maximum and use the o-ring from the old part.
★★★★★
★★★★★
John O - April 17, 2023
Verified Purchase
Agitator replacement
The replacement part fit perfectly and easy to install. Part ordering and shipping was easy and efficient.
★★★★★
★★★★★
Lynn S - March 31, 2021
Verified Purchase
Simple easy repair
Part was not exact for my machine though was easy to navigate through using instructions
★★★★★
★★★★★
Edward W - October 28, 2020
Verified Purchase
Agitator Replacement
I was surprised how quickly the order was shipped. Exactly as ordered, it fitted perfectly.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 5.0 / 5.0, 7 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Agitator top section was broken
Loosened set screw, removed agitator, installed new agitator and tightened set screw done
Other Parts Used:
Beverly from Conehatta, MS
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
60 of 76 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator not agitating
old agitator stripped plastic splines. pulled up and out old agitator, aligned and pushed (hard) down new agitator, tightened nut. easy-squeezy!
Other Parts Used:
Steve from Check, VA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
27 of 34 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The top part of the agitator was loose and would rotate.
A 5/16 socket on a ratchet was used to loosen a screw. Remove the agitator from the splined shaft by pulling straight up. Slide the new agitator onto the splined shaft and tighten the new supplied screw.
Other Parts Used:
Michael from East Liverpool, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Socket set
21 of 24 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Agitator was slipping,
Removed 1 screw with 5/16'' nutdriver on lower area of agitator and unit slipped off spline like butter. Replaced with new unit and simply tightened the holding screw. Repair Dude wanted 179.50 for this repair. I saved over $100.00 doing this myself. Cool.
Other Parts Used:
Scott from Lac du Flambeau, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
15 of 19 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top auger section won't stay locked together
Ordered a new replacement agitator, removed the old agitator with the loosening of set screw on the base of agitator, which slips over the gear spline and installed the replacement agitator, tighten the set screw with nut driver, OH, you have to use the fabric softener cup, which snaps off the old agitator and install it on the new agitator. Wha-la!
Other Parts Used:
Manuel from Vacaville, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
14 of 19 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Top of agitator was loose and would come off.
I removed the nut from the bottom of the old agitator, slipped it off and put the new one on. After tightening the nut it worked just fine.
Other Parts Used:
Wayne from La Grange, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
12 of 17 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
agitator didn't turn
Took out one screw, set new on in, rescrewed in. Just remember to keep your fabric softner cup. Super easy. We paid for next day delivery, and it arrived by 9:00 a.m. the next day.
Other Parts Used:
Theresa from Prescott, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
9 of 13 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
12 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Judy
September 10, 2017
The agitator separated into two pieces. The base that has the bolt that requires a nut driver to remove stayed in its locked position. I put the top part( not fluid cup) on the base turned until it went down into place. It floated to the top again. Couldn't keep it on the remaining base. Would a new agitator assembly eliminate the problem and keep the radial fin part locked to base of agitator. Thank you
For model number LAV3600AWW
Hi Judy,
Thank you for your inquiry. Yes it would. It looks like the manufacturer now makes that all as one complete part. Good luck with your repair.
8 people found this helpful.
Was this helpful?
Thank you for voting!
Kathy
February 18, 2018
We have the agitator out. Should it rattle when you shake it?
Hi Kathy,
Thank you for your question. It should not. The cogs in your agitator might be broken and you may need to replace the part. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Joe
March 18, 2018
Under the agitator is a screen. Is that removeable to be cleaned? I am replacing the agitator but the screen looks very dirty.
For model number LAT3600AAE
Hello Joe, Thank you for your inquiry. Yes, you can pull this part out to clean it. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Vicki
April 4, 2019
My replacement agitator will not stay on it comes loose during the spin cycle and rises up,i have to push it down and keep tightening the screw during the wash cycle. Is there a way to keep it in place.
For model number LAV3600AWW
Hello Vicki, Thank you for the question. I suggest checking to make sure the o-ring is with the screw and it is not wore or the screw is not stripped and needs to be replaced. PartSelect Number PS2019801. Hope this helps, good luck with this repair!
Will your part number ps2019803 fit in model number pav3300agw . Thanks
For model number PAV3300AGW
Hello Anil, Thank you for contacting us. I am not showing PS2019803 is a compatible part for this appliance. I have researched the model you have provided and have found the base for this model is PartSelect Number PS2017908. The Upper part of the agitator is PartSelect Number PS2018203. I looked up the part and it is listed as No Longer Available/Discontinued. There is no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. Hope this helps!
Agitator not agitating. Base turns freely clockwise and does not engage agitator but when turning counter clockwise it engages the agitator. When in the washer it spins clockwise during wash and counter clockwise during the rinse and spin. But will not agitate during wash.
For model number LAT8416AAM
Hello John, thank you for writing. The two main parts to check out are the Belt Kit PS2005284 and the Agitator Auger and Base Assembly PartSelect Number PS2019803. We hope this helps.
Hi, the agitator i have has the base and fin part seemingly like two pieces...although i cannot get them apart, there is about a half inch of wiggle room where the top (fin part) can be pulled/pushed up and down. is this its normal function or is it broken?thanks,tb.
For model number LAT9356AAE
Hello TB, thank you for your question. The top part of the agitator will be able to be moved up and down a little bit, but it will not come apart. This is the normal function of the agitator. They won't actually come apart into two pieces. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Larry
November 9, 2019
So I put a new agitator in and the agitator shaft came out. Can I just push that shaft back in the washer?
For model number LAT9416AAE
Hello Larry, Thank you for the question. As long as the shaft is not damaged, it should be able to be pushed back in place. Hope this helps!
Was this helpful?
Thank you for voting!
Lisa
November 20, 2018
I believe there is a necklace stuck in the agitator. We are trying to remove the agitator but we read that the screw is on the side. We do not see one on side, but a bolt on bottom or fabric softener dispenser. Is this correct, we are worried to break the dispenser but cannot release the bolt.
For model number maytag mvwc565fw
Hi Lisa,
Thank you for your question. There is a video listed with the part you have referenced in your question to us that may help you remove the agitator. I hope this helps. Thank you and have a great day!
Was this helpful?
Thank you for voting!
Steve
November 29, 2017
When I pull up on the agitator assembly, it comes out with the drive shaft. I can look right down through the seal into the transmission. What keeps the shaft in place? It does not sound right to me that the shaft should pull out. If I load it with sheets and towels the screw action causes the agitator to lift just enough so that it stops turning. What part will fix this and how?
For model number LAT2301AAE
Hello Steve,
Thanks for your question. There is a screw on the side of the agitator which may be loose or missing. Check that to see if there is any problem with the screw. If not, the agitator itself may need to be replaced.
I hope this helps.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
