The electronic control board manages the washer's functions such as filling, washing, draining and spinning.
How Buying OEM Parts Can Save You Time and Money
Troubleshooting
This part works with the following products:
Washer.
This part works with the following products:
Amana, Whirlpool, Inglis.
Part# WPW10525371 replaces these:
AP6022637, W10253240, W10306715, W10525371
Customer Repair Stories
Average Repair Rating: 4.3 / 5.0, 1 reviews.
What's this?
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Machine would not drain
After removing the front access panel, i found the troubleshooting guide with the code sequences taped to the panel, which explained the how to read the trouble code the machine displayed. Before changing the control board, I first checked the drain line, the coin/lint trap, the pump impeller, and then moved to checking the trouble codes. You will need to remove the top of the machine to access the control board, but this is very simply a matter of removing 4 screws on the rear of the machine and sliding the top back and lifting it up and out of the way, which will expose the control board on the top right side of the machine. The control panel simply slides to the rear to release from the machine. I took a photo of the control board before disconnecting all of the wires, there are about 10-12 connections, and when the new part arrived, simply slid the new control board into place, replaced the connections, replaced the top on the machine, slide the machine back into place, and did a small load of laundry to test. I have now ran 10 loads and everything works great. Great OEM part and very simple to install.
Other Parts Used:
Larry from Granite City, IL
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Aaron
January 13, 2022
We experienced a power outage and afterwards the washer won't start. I unplugged and waited a few minutes then plugged back in. There is a continuous beeping. This stops after I push the start button. When I push the start button again the rinse light blinks once and a single beep sounds. That's all the machine will do. It was manufactured in 2011 but is not in a primary usage home so hasn't been used very much compared to a normal household usage.
For model number WFW9050XW00
Hello Aaron, Thankyou for the question. With a power outage it can cause a surge that will damaged one or both of the control boards. We suggest checking the board to see if they have the proper voltage and if there is any evidence of burn marks or a short. We hope this helps!
this machine has problem starting. when started it runs and fills as it should ,after 2-3 minutes it stops and beeps when restarted by pushing start or unplugging and replugging unit the water drains, spins a minute and stops again. this can be repeated 3 or 4 time and then it will run as it should. next load same thing occurs. any sugestions as to what would cause this. thanks
For model number nfw7300ww00
Hello Leland, Thank you for your question. Researching the model number that you have provided, there are several parts that can cause this issue, the door lock latch, the motor control board, the grounding microswitch, the drive motor, the drain pump, or the washer function control board PS11755972. Check the control boards for any visible damage or loose connections, and you can test the other parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. We hope this helps with your repair.
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is found between the m...
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
[{"position":0,"name":"Home","title":"Home","url":"/"},{"position":1,"name":"Circuit Board or Touch Pad","title":"Circuit Board or Touch Pad","url":"/Washer-Circuit-Boards-and-Touch-Pads.htm"},{"position":2,"name":"WPW10525371","title":"WPW10525371","url":""}]
