This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the oute...
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
Water inlet valve controls the water flow into the washer.
Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW...
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is...
$63.96
In Stock
Questions And Answers for WFW9050XW00
Ask our experts a question about this model and we'll get back to you as soon as possible!
13 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Margarita
December 7, 2019
Porque mi lavadora le pongo el ciclo de lavado y después de dar varias rotaciones se detiene y prende la luz de wash y deja de continuar y la tengo que apagar para que bote el seguro de la puerta
For model number WFW9050XW00
Hola Margarita
Gracias por tu pregunta. Desenchufe la lavadora o desconecte la corriente. Espera 5 minutos. Enchufe la lavadora o vuelva a conectar la alimentación. Ejecute otro ciclo. ¡Espero que esto ayude!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Bruce
January 12, 2020
Washer wont go onto high spin cycle
For model number WFW9050XW00
Hello Bruce and thank you for writing.
It certainly sounds like it could be a faulty or loose belt PS11746258, you should check for signs of damage, and replace if necessary. We hope this helps. Please contact us anytime if you require further assistance.
Stops and beeps, seems to be beeps and the lights 2x, stops and then again
For model number WFW9050XW00
Hello and thank you for writing.
This could possibly indicate a malfunctioning door lock latch PS11751211 and/or possibly a faulty temperature sensor PS11755214. We hope this helps. Please contact us anytime if you require further assistance.
When pushing the button door locks no water dispense within 10 minutes washer makes sound cycle to wash is over but you cannot open the door after two minutes it beats to cut off and then you can open up the door but it has done nothing :
For model number WFW9050XW00
Hi Arnita, thank you for contacting us. If the washer is not filling with water. There are some parts that you will need to check to see which one is causing the issue. The parts that fix this issue the majority of the time are the water inlet valves. Before testing the water inlet valves, make sure that the washer has been unplugged from the electrical outlet. From our website, the water inlet valve will most likely be found directly behind the hose connections. You will need to remove the rear panel in order to access it. Once you have located it, remove the valve in order to test it. Before testing it, inspect the screens inside the valve and the valve itself for any debris or damage. Be very careful when doing this as screens cannot be replaced, and if they become damaged the valves will need to be replaced. Set your multi-meter to Rx1 and touch the probes to the terminals. The reading of a functional valve varies from model to model, refer to your owner’s manual to determine what your reading should be. If the readings are not what they should be the valves will need to be replaced. If the valves are fine you will need to check both the water level switch and the hose that it is attached to. Inspect the air dome hose by submerging it in water, sealing one end and blowing in the other, no bubbles should come out of the hose during this test. Additionally, you should inspect it for any signs of wear or damage. You will need to remove your appliance’s cabinet to access the air dome hose. Remove the water level switch to. It is usually found below the control panel but may also be found below the sump area below the tubs. Inspect the switch for any signs of wear, burning, cracking, or damage. If the air dome hose is not damaged or if your switch shows any of the symptoms above, replace the switch. We hope this helps!
The machine goes through most of the cycle then stops and beeps, then the "add garment" light comes on. What do i need to fix it?
For model number WFW9050XW00
Hello Allan,
Thank you for your question. This is normal for your washer, this option is available in all wash cycles except Rinse & Spin, Drain & Spin, and Clean Washer with AFFRESH TM cycle. When this option is available at the beginning of the cycle, the Add Garment status light will illuminate for approximately the first 7 minutes. This washer allows a 7-minute period in which other garments may be added to a load. We hope this helps.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.