Average Repair Rating: 4.5 / 5.0, 12 reviews.
What's this?
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
door insert all scatched up
Took me a while to figure out that the bottom plastic strip is all that holds in the panel. Once it is removed , it pulls out easily When the new panel arrived,just slide it up into the top grooove, and push the bottom strip back into its groove. The front looks like new!
Other Parts Used:
stephen from west islip, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
24 of 28 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door panels and trim damaged by power wheelchair
I removed the four screws, two at the bottom and two at the top, of the lower access panel and removed the broken assembly. I removed the piece of rubber trim from the bottom of the door panel (unsnaps from it's channel). I pried off the damaged bright trim from the left side of the door, scraping off most of the glue residue with a knife and finally cleaning the rest with solvent. I cut the new piece of bright trim to fit with siscors and pressed it in place. I used the remainder of the new trim and a piece cut from the old damaged trim previously removed to trim the lower access panel. I carefully removed the insulation from the old access panel and installed it in the new access panel with double sided tape. I followed the instructions that came with the new panels and installed them in the door and access panels. I reinstalled the rubber trim in the bottom chanel of the door. I moved the other parts from the old access panel to the new access panel and reinstalled the new access panel assembly with the four screws removed earlier. Finished... I found other sites with the parts but ordered from PartSelect because your site made it easier to identify and select the right parts to order. My order shipped very quickly and everything arrived perfectly. I'm impressed. Thank you...
Washed the edges good and clean to remove old tape that was holding the old panels. Slid in the new ones and found that the retaining strip would not work without replacing the inner strip. I didn't want to order this $53 dollar plastic strip so I squeezed a couple of rubber pieces into the bottom of the side edges to hold the top panel. Placed the retaining strip in place and used a long strip of black duct tape at this bottom edge to hold it all. It works and the new panels make the dish washer look close to new,the black duct tape hardly shows. This works good for my 10+ year old dishwasher until it is replaced with one that has a better door design.
Pulled off the bottom trim, slid the old panel off and put the new panel on. Then popped back on the bottom trim.
Other Parts Used:
Luann from Springfield, MO
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
4 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
door panel was damaged and the cover over the buttons was torn.
Label cover was glued on and you simply pull it off and replace it with the new one. That takes about 2 minutes! The front panel was dented and all you have to do is pull off the rubber trim on the bottom and replace the panel. The dishwasher looks new!!
Remodeling a house and front panel on dishwasher was bent and needed replaced. I just measured panel and ordered without a model or part number. Was so lucky the panel fit perfect.
Just took old panel off and went side to side and then slide panel under front trim. Of course it was easier because the bottom door trim was off and now I have to find that replacement part. Not having any luck with that!
Other Parts Used:
Sylvia from WHITESBURG, KY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
changing a damaged door panel insert
I needed to cut 1/4inch off the panel and unscrew the side piece which held it in place.... insert the new piece and put back the 3 screws. Done!
Other Parts Used:
Constance from Sonoma, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
1 of 2 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Color didn't match updated look
First I removed the the rubber sides. Then I slide the replacement panel over the exisiting one. That's it no other tools were needed. I didn't even break a sweat.
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
13 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Liz
April 26, 2018
What are the dimensions of this panel?
Hi Liz, Thank you for the question. Going by the 1 inch grid, the panel is measures approximately 23 1/2" X 19". Hope this helps!
7 people found this helpful.
Was this helpful?
Thank you for voting!
Lois
November 15, 2018
What door panel do i need for this model. My black panel is damaged.
For model number DU8500XB-0
Hello Lois, thank you for your question. The door panel insert for that unit is part number PS11741289. This is white on one side and black on the other. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Nancy
January 14, 2019
Is there a panel to replace the lower black panel (below the door) of the dishwasher? If so, what is the part number?
For model number DU900PCDB3
Hello Nancy, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Part Number: PS11741275. Thank you for your inquiry, good luck with this repair!
Can i get a stainless steel insert for this model?
For model number 66515595792
Hi Paul,
Thank you for your question. Unfortunately this panel is only a reversible black and white. I hope that helps. Good luck with your repair.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Suzanne
February 4, 2020
I would like to change my color from black to white by changing the door panels. I can find a replacement for the door panel but can't seem to find a replacement for the bottom panel. Can you tell me if one is available.
For model number DU920QWDB3
Hello Suzanne, Thank you for the question. Very sorry but the Bottom Panel is only made in Black. For more specialized assistance or to speak with someone about this, I would suggest calling the manufacturer of the appliance directly. We hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Woody Patterson
February 14, 2020
Need black front door and control panel replacement for this Kenmore modal. Can’t seem to locate
For model number 665-1311 4k701
Hello Woody, thank you for your question. The control panel in black is PartSelect Number PS11748198
and the door panel in black is Part Number: PS3418314. I hope this helps.
The above is a Whirlpool model dishwasher, we need a new door panel. It is almond but if white is only available we’ll make it work. Thanks
For model number DU8700XY5
Hello Steve, thank you for inquiring. The Door Panel for your model is part PS11741289. It is reversible, one side being white and the other is black.
Was this helpful?
Thank you for voting!
Nancy
November 23, 2019
I just ordered the door panel insert for my dishwasher and cannot figure out how to get it in. There were no instructions.
For model number RUD3000HG0
Hi Nancy, I could not find any information on model RUD3000HG0 so I am unsure if it is compatible, I would double check the model number as it may not fit if it isn't a correct part. Thank you for your question and good luck with your repair!
Was this helpful?
Thank you for voting!
Teresa
December 20, 2019
So my retainer (wpl 3370441) for the front panel is missing and my cover got bent up. Ordered a new panel and it is on its way! (yay!) cannot find the retainer panel part anywhere as it has been discontinued by Whirlpool. Any suggestions for a remedy so that i don't mess up my new panel?
For model number DU8016XX5
Good Day Teresa. Thank you for your question in regards to your unit (Model Number DU8016XX5). We would recommend reaching out to the manufacturer as they may be able to advise of an alternative part that would be compatible with your unit. They can be reached at by phone by calling 866-698-2538. Best Regards.
Was this helpful?
Thank you for voting!
Nancy
February 21, 2020
Can't find my exact model number. Does this part fit my old dishwasher, model # above?Thank you!
For model number DU927GWDBO
Hello Nancy, thank you for your question. Yes, that part does fit the above model. I hope this helps.
Fresh Flow Produce Preserver is made for your refrigerator to help keep produce fresh for longer by absorbing the chemical, ethylene, that causes your fruits and vegetables to ripen quicker. Your produce could be fresh f...
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This powerful washing helpe...
Affresh dishwasher Cleaner is specially formulated to help remove limescale and mineral build-up that can be unsightly and could affect your dishwasher's performance. Each tablet is designed to clean inside your machine ...
Make your cooktop shine with Frigidaire ReadyClean Glass and Ceramic Cleaner. Our scratch-free, streak-free formula removes smudges, grease, burnt-on food, dirt and oil, while protecting and polishing to repel dust and d...
