YMER8875WS1 Maytag Range - Instructions

I removed all the screws that held the trim and inner frame to the outside window unit first. Then, I removed a protective glass from over the two inner panes. Next after removing the frame that held the two inner glass panes together, I took the broken inner glass pane out and replaced it with the new one. Then basically I just retraced my steps and had the door put back together in about 45 minutes. You just need to pay close attention to your disassembly so that you are able to put the pieces back together quickly.

Slid oven out and took back shield off unplugged sensor took bracket screw out replaced sensor with new one.

Turn off breaker to oven and verify no power.
Remove the two screws holding metal panel covering baking element on the floor of the oven (near back of inside of oven)
Remove two screws holding element mount to floor of oven (near front of inside of oven).
Remove single screw holding element to back wall of oven.
Pull element toward front of oven, carefully holding wires so they do not disconnect from element and slip inside the ovenback wall.
When you can reach the wire connections, hold each one with a pair of pliers and disconnect from element ends.
Connect new element ends into wire connections. Be sure to insert all the way into both connectors.
Carefully, push the wires back into the rear of the oven, trying not to scrape the wires on the sheet metal.
When fully inserted, reinstall single screw to secure element to back wall.
Re-install two screws to element mounting at the front of the oven floor.
Re-install two screws to secure element cover plate to the floor of the oven.
Turn on breaker for oven and verify oven has power.
Turn on oven to bake at 400 degrees.
Wait for oven to come up to temp and maintain for 10-15 min (you may smell some burning smells as the element heats up the first time).
Enjoy...

First I removed the two wires from the back of the stove. I then removed the two screws that were holding the element in place. Installed the new one without problems

Door was removed very easily. Outside trim pieces were removed. The rest came apart like a simple puzzle. Inside glass is very easily accessed. Upon assembling, time was well under an hour. Shipping was fantastic and I saved close to 200dollars between a service call and a repair.

Unplug appliance, unscrew small cover plate in rear. Disconnect wires from old element, may need to use needle nose pliers to wiggle clips off. Open oven door, remove false bottom to expose baking element. Remove baking element. Install new element, connect wires from rear, and replace covers and false bottom. Plug in appliance and test.

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

removed bottom pan cover. removed broken element. replaced with new one.. simple. would buy from this place again. shipped super fast

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Hired a pro. Parts are difficult to get on a timely basis today , if at all. Screw up this repair by damaging the outer " black glass " and you buy a new stove. It took three weeks to get my replacement glass even though PS said the part was being sent within a day of the order. Even so , I am am happy to have gotten it , and will continue to use the company.

I shut off the breaker to the stove. I removed 2 screws from the underside of the cooktop at the front of the unit. I raised the cooktop and had my helper hold the top at an angle to access the burner. I removed 2 screws attached to the burner and then loosened the 2 clips and moved them to release the burner. I transferred the electrical connections from the old to the new. Reinstalled the burner and cooktop. Turned the breaker on, tested the new burner and I was fone

Watched video & did just guy in video did. Very easy job & the burner works like new.

Remove the door.
Remove screws
Clear out broken glass. Vacuum out small glass shards.
Clean all glass.
Reattach all parts.
Replace the door.
Smile!

First things first...Unplug the unit...Then remove the center plate from the back of the oven (one screw) and take clips off element. Then on the inside, there are 2 screws near the back on the bottom panel. These were rusted on pretty good, so that's where the vice grips came into play. The entire job would've gone much faster, if I wasn't fighting with these 2 screws...After you remove the screws, tilt up bottom panel and remove. Then you just remove 1 rear screw & 2 bottom screws and slide out the old element. Slide the new one in, secure it with the screws and screw the bottom panel back into place. Go to the rear of the oven, slide the 2 clips on the element and screw rear plate back on. Plug the oven back in and that's it...

Watch the video. Spot on instructions. Easy peasy.