Models > WTW6300SW1 > Instructions

WTW6300SW1 Whirlpool Washer - Instructions

All Instructions for the WTW6300SW1
91 - 105 of 107
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Won't drain the water
It was not easy but I dit my sell
Parts Used:
Drain Pump
  • Jose from Verobeach, FL
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set, Wrench set
Was this instruction helpful to you?
Thank you for voting!
UL flashes, will not spin, really loud,& black spots under washer
We ordered the outer tub & bearing and now the washer works like it was brand new.
Parts Used:
Outer Tub Assembly
  • Elijah from Point Hope, AK
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Socket set, Wrench (Adjustable)
Was this instruction helpful to you?
Thank you for voting!
did not work
reemplace the lid lock assembly
Parts Used:
Washer Lid Lock Assembly
  • JESUS from PORT ARTHUR, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Water would not drain
I read the directions on this web site and was able to install the new drainage pump in about 30 minutes. I suprised myself. Thanks.
Parts Used:
Drain Pump
  • Neil from Onalaska, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Pliers, Screw drivers, Wrench set
Was this instruction helpful to you?
Thank you for voting!
machine gives uneven load alarm and f51 error code
Tilt the machine over to access the bottom I rested it on a dolly.remove the rotor with an allen wrench .then rmove the 4 bolts on the stator .then lift it off the main shaft and unlug the sensor wires . just reverse the process to install the new one (be sure to allign the arrows on the sensor and the stator when reistalling. I wish i could say this solved my problem .my machine runs untill the spin cycle then it starts shaking and gives the uneven load alarm again.
Parts Used:
Motor Stator Assembly
  • Charles from Houston, TX
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
Washer was noisy and had a lot of movement
The rod kit fixed the issue. I cant really explain how I did it, because I dint know if I did it the right way.
Parts Used:
Suspension Rod Kit - Set of 4
  • Shawn from Indio, CA
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers, Socket set
Was this instruction helpful to you?
Thank you for voting!
Code F51 Washer would not spin.
I disassembled the top half of the machine removed the drum and found a bad bearing. The code F51 said i had a bad motor control board. I had a frozen bearing on the main shaft. Freed up bearing, machine now runs but I need to replace the bearing,
Parts Used:
Electronic Machine and Motor Control Board
  • Fred from Valparaiso, IN
  • Difficulty Level:
    Difficult
  • Total Repair Time:
    1- 2 hours
  • Tools:
    Socket set
Was this instruction helpful to you?
Thank you for voting!
The seal was broken on the agitator cap barrier
Removed the fabric softner at the top of the agitator (needed a screw driver to pry it loose) and reached in to grab the barrier with my hand and pulled it out, very simple to do.When I put the new one in I put some liquid soap on the gasket and it snapped right into place.Very easy to do, all is well now, thanks Part Select.
Parts Used:
Washer Agitator Cap Barrier w/Seal
  • Ralph from New Milford, NJ
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Lots of gunk between fabric softener dispenser and where it attaches to the agitator
Rubber O ring around the Inner Cap was rotted and busted through. Replaced with new Inner Cap Seal. Easy as pie!
Parts Used:
Washer Inner Cap Seal
  • Gregory from Sandy Springs, GA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Replace a seal
Just had to remove cap on agitator and replace new rubber seal.
Parts Used:
Washer Inner Cap Seal
  • Janet from Colfax, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
drum made loud noise
put machine on side pushed old rods out to top installed new ones. runs like new. tried to ask mechanics or stores nobody would help with info, they all want to send mechanics with 80$ just to get here. it was easy to do. thanks
Parts Used:
Suspension Rod Kit - Set of 4
  • axel from lighthouse point, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
vigoirously shaking causung UL code
Replaced rods with new set of 4
Parts Used:
Suspension Rod Kit - Set of 4
  • Josh from Lodi, CA
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
Every wash cycle would throw out the "F1" code and I would have to keep changing the wash cycles until one would finally catch. Replaced Motor Control Board and now works excellent!
Read the previous reviews and showed my son the diagram which he then replaced the part in about 15 minutes. No more hassle and works like a charm :)
Parts Used:
Electronic Machine and Motor Control Board
  • Bonnie from Baytown, TX
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
replace suspension rods
took top off.2.replaced rods one at a time.placed top back on.very simple.evan got new bushings for the top.very simple process.no skills required.
Parts Used:
Suspension Rod Kit - Set of 4
  • brett from seymour, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Nutdriver
Was this instruction helpful to you?
Thank you for voting!
broken seal
went well but alas the problem still exists.
Parts Used:
Washer Inner Cap Seal
  • Lorraine from Millsboro, DE
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WTW6300SW1
91 - 105 of 107
Back to Top