Models
>
WM3431HS
WM3431HS LG - Overview
Models starting with WM3431HS
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Washing Machine Drain Pump
PartSelect #: PS3579318
Manufacturer #: 4681EA2001T
The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$156.41
In Stock
Washer Motor Rotor Position Sensor
PartSelect #: PS11706506
Manufacturer #: 6501KW2001B
The sensor monitors the direction and speed of the spinning rotor.
$40.43
In Stock
Washer Tub Bearing, Rear
PartSelect #: PS11711138
Manufacturer #: MAP61913707
This tub bearing is for washers.
Tub bearing supports the spin basket shaft at the tub.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
$71.07
In Stock
Shock Absorber
PartSelect #: PS3522311
Manufacturer #: 383EER3001G
Sold individually.
$59.81
In Stock
Gasket
PartSelect #: PS3522854
Manufacturer #: 4036ER2003A
This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is le...
$39.46
In Stock
BEARING,BALL
PartSelect #: PS7785069
Manufacturer #: 4280EN4001C
The tub bearing supports the spin basket shaft at the back of the washing tub. If your washing machine will not spin, is leaking water, or if there is a loud screeching noise during the wash cycle, th...
$81.26
On Order
CAP,DRAIN HOSE
PartSelect #: PS3635866
Manufacturer #: 5006EN3015A
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
$10.26
In Stock
Pump Filter
PartSelect #: PS3522306
Manufacturer #: 383EER2001A
This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your wa...
$34.13
In Stock
Common Symptoms of models starting with WM3431HS
[Viewing 10 of 10]Will not drain
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Draining Issues
Fixed by
these parts
these parts
Show All
Engine runs but does not pump water
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Water Filling Issues
Fixed by
these parts
these parts
Show All
Noisy and Marks Left on Clothes
Fixed by
these parts
these parts
Show All
Noisy
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Parts Used:
-
Jorge from Apple Valley, CA
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Screw drivers
559 of 712 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
noisy operation, sometimes did not drain, gave OE code
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Parts Used:
-
Michael from RALEIGH, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
47 of 61 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pump rotor broke off shaft.
There are two pumps in this system. I turned the washer on its side and took off bottom plate. There are several screws holding this on. I then took the entire pump assembly off. There are 3 screws holding each pump on the brown plastic body. Each pump has a positive and negative lead. I switched out the pump and reassembled. The hardest part is getting the 3 "shock absorbers in place with the rubber sleeves. I think the book suggest getting to the pump from the front side but I went through the bottom. Worked good. I did wonder however if the other pump was working. Do you need two pump working to get flow? By replacing one pump I went from no flow to good flow. Cost me $75.00
Parts Used:
-
Bill from COTTAGE GROVE, WI
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
23 of 31 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!