The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
This door boot is for washers.
Door boot forms a seal between the wash tub and the door, preventing leaks.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is brok...
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
This drain hose plug, also known as a hose cap, is a genuine OEM part for your washing machine. This plug caps the drain hose from the pump housing, and helps prevent leaks from your washer. Before be...
This part is the replacement rear tub gasket for your washer. It is made of black plastic and is approximately 3-1/4 inches in diameter. The rear tub gasket forms a watertight seal between the rear tu...
$39.25
In Stock
Questions And Answers for WM3370HRA
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
MOHANREDDY
December 19, 2022
FOR ERROR CODE P E . WHICH PART NEEDSREPLACEMENT AND HOW MUCH IT WOULD COST
For model number WM3370HRA
Hello Mohanreddy, thank you for reaching out. The PE error code indicates a problem with the pressure level sensor. This sensor monitors how much water is in the machine, also telling the control board if it's been filled or emptied. We would recommend replacing it, the part number is PS3529317. If you need help placing an order for it, please feel free to give us a call. We look forward to hearing from you!
Hi Shantilal, thank you for the question. The UE code indicates that the washer is attempting to balance the load, which may be the result of the unit not being leveled correctly or the load itself. To solve this issue, first, you may need to make sure that the load is balanced inside the tub. If the load is balanced, then you may need to check the leveling legs, part number PS7788210, which help keep the washer balanced and stable during operation. You may need to adjust the leveling legs, or if they are faulty, you may need to replace them. We hope this helps!
For error code OE what part do I need and how I can do it myself
Thank you LG
For model number WM3370HRA
Hello Michal, thank you for your inquiry. The OE error code indicates that the washer is unable to drain the water it used during the wash cycle. We recommend you replace the drain pump, part number PS3579318. Before replacing the drain pump, make sure the drain hose and filter are not clogged. We have attached a relevant link that can help you replace the drain pump. We hope this solves your problem!
Was this helpful?
Thank you for voting!
< Prev
1
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
