WM2277HW LG Washer - Instructions

We followed the installation video step by step that was found on another website.

Very simple. Watched video.
Pulled the washer out to get behind it.
Turned off water supply, unplugged it.
Unscrewed the screwesholding the top in place, slid top back, lifted it off.
Used pliers to open the clamps holding the pipes to the valve - one at a time. And fitted the pipes to new valve, one at a time.
SOME WATER REMAINS IN THESE PIPES, SO PUT A TOWEL UNDERNEATH TO CATCH IT.
Removed the electrical connectors one at a time and fitted them to the new valve one at a time.
Did same to the hot valve - not leaking but decided to replace it before it did leak.
Reattached water supply hoses and electric plug.
Tested the washer cycle to make sure no leaks.
Put top back on and pushed washer back to wall.
Apart from the testing, the whole job took 25 minutes.
The parts arrived on Day 2 after the order.
VERY PLEASED WITH EVERYTHING!

Removed top of washer
Then removed front
Then reversible basket ,during spring depressed pliers
Put new gasket on inside flange first put spring back on
Put front washer panel back on and put screws back in panel holes
Put door seal on front flange and reinstalled spring on new door seal.Put too back on and finished clean up

Not too bad, had a neighbor help with the project as washer/dryer were stacked. removed dryer from on top out of way. Drained washer, tilted on side to get access from down below. Second person help here. unscrewed drain pump from front, Used pliers to unclamp hoses, disconnect wires to motor (already pulled power from wall) pushed plastic clip holding in unit and pulled out. New unit was factory new, not a knockoff. We took extra time to clean out hoses, especially from the main washer unit, it was a simple unscrew clamp and pull hose down. We sprayed out gunk from hoses and parts going back in. Once new unit was ready, installed back and reconnected hose and power. The clamps were somewhat of a pain with the overall size and angles to get them seated and on correctly. Much easier to take off, but take the time to reinstall correctly. Don’t need water leaking. Motor much quieter now, wife is happy.

bought a position sensor
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour

Honestly youtube but pretty simple install.

I followed the instructions of your instant repairman. A Phillips screwdriver was the only tool needed. Thank you .

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.

Google LG washing machine bearing replacement, you'll find a very informative video narrated by a British gentleman who will walk you through the steps. If you are even a slightly handy DIY'er this is an easy job although very time consuming. Take your time with reassembling the machine. I missed a couple of connections and while testing it out I flooded the laundry room. Could have been avoided if I had taken a picture of every individual item I disconnected.

Watch the video to repair and follow along

Watched a YouTube video on how to disassemble the washer step by step, replace the bearings, and reassemble the machine. was very helpful.

Started with some resin paper on the floor, some painter’s tape, and a sharpie to keep track of screws and removed parts (painter’s tape to stick hardware to). Set up iPad on dryer and followed every step by step instruction by pausing the video. The instructions were perfect (but would have liked some more close up shots). Installation of new bearings was exactly as demonstrated and truly appreciated the step by step descriptions to put it all back. Hardest part of the repair was replacing the wire ring on the rubble gasket — only step not displayed. Suggestions for future repair videos: 1) how to organized hardware as removed; 2) more close ups; 3) a video showing the problem at the start followed by a video showing post repair. As a visual person, I have spend the past few days watching the spin cycle wondering if there is a wobble or shudder etc… Similar to the feeling of buying a used car…every clunk or shudder gets you worried. Love that I saved $1000 plus taking on the repair.

Follow the LG washer video.

I researched the symptom, watched a repair video, ordered the parts: one rear bearing, seal, and gasket. After disassembly found inner bearing to be bad. Ordered inner bearing. Then found the spider or hub shaft corroded, and ordered spider. Finally with all the parts replaced, assembled washer and returned it to service.

I followed various tube videos. The vides were very easy to follow.
But the most important thing to have to do the job is washing machine spring removal tool. This tool I had to order it online unable to locate in store.