WM2077CW LG Washer - Instructions

From previous experiences with other washers, i.e., Sears, I decided it was the mother board or the door latch component. Ordered the electronics and then the discovery that LG has an APP for iPhone. Loaded the app, placed the phone next the washer and pushed the button on the washer. The washer "talked" to the iPhone and within 15 seconds it told me there was a problem with the thermistor. Opened the back of the washer and looked under the tub for the thermistor and found the 2 connecting wires were hanging loose. Put the wires back into the thermistor connection and everything was back working.

YouTube is your friend for many such repairs. See this link for an overall description:

https://www.youtube.com/watch?v=WuvLuC8x4_s

I had to remove the top panel to determine exactly which valve was leaking. It turned out both hot and cold-water valves were defective.

After unit is unplugged and top is removed, it's a simple matter to remove/replace hose connections and electrical connections. It took me less than an hour to complete the task once parts were in hand.

Again, YouTube is your friend for such repairs.

I actually did the repair exactly as the video showed. If I would have had the part at the time of discovering the problem it would have been about a 45 minute repair from start to finish. Worst part of the whole fix was moving the heavy washer.

Unplug and disconnect water lines. Move washer out. I used soapy water to make it easier to slide because it is stacked washer and dryer. Slid dryer onto large trash can saving my back. So easy. Make sure it is heavy duty . Removed lid. Removed old part by removing to screws in back. Disconnected 3 wires, disconnected one hose at a time while reattaching each one to new part. That way I was sure to get them back in the right place. Attached back to machine . Put water hoses back on and checked for leaks before but lid and dryer back in place. Ta da!! This was so easy. I am a 57 year old woman and this was pretty simple. I tried trouble shooting by using tub cleaner and everything as manual suggested but it still leaked. Watch a lot of you tube. Apparently lg has this happen with this part a lot. Thank you parts select. I’m sure this saved me a lot of money. I have had enough money bleeding from my pockets with bigger home problems. Thank you.

Figured out how to take off top of washer, look inside for problem, ordered new part, watched video how to replace part. All on line. $65.00 later and my 19 yr old washer is still working awesome.

Super straightforward to diagnose and repair.

There was puddle under the washer.

I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.

Two hose clamps to remove and replace, then replace the top and ready to go.

2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.

The video from PartSelect showed removing the retaining ring from the rubber washer tub boot to then allow access the door lock located behind the boot for replacement. That ring can sometimes be a real pain to put back on. This can be avoided altogether!

It's much easier to access the door lock switch by removing the two retaining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.

Please note that the washer should be unplugged from power while working on any electrical component.

Took out old sensor and put in new one.

Remove door assembly from the hinge, unscrewed screw from the panel. Leave couple screws to hold Hinges. Remove the rubber seal but stretching to spring out, not having rt tool (long nose plier). Remove rubber partially close to the hinge. Remove the Hinges and replaced it, then reverse putting together back. Use small screw driver to put spring tensioner back. Reinstall frame door to hinge, double check everything.

WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.

Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!

After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went so I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.

Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.

Unscrewed 2 screws holding part. Removed old part & replaced with new.

Remove where the water pumps are and remove the one that was damaged easily

ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!