This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This door bellow, also referred to as a door seal gasket, is an OEM replacement component designed for various front-load washing machine models. Made from flexible gray rubber, it forms a secure barr...
This front-load door hinge is a genuine replacement component designed to support the door on compatible washers and dryers, ensuring smooth and secure pivoting during opening and closing. Constructed...
This hose attaches to water pump assembly.
NOTE: As per the manufacture if the washer has an Eco Ball, it's no longer needed when the new hose is installed.
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
Having a problem with a funky-smelling washing machine, or one that just doesnt seem to clean your clothes as well as it used to? Say hello to the Affresh Washing Machine Cleaner by Whirlpool. This po...
This door lock/latch assembly is an OEM replacement part for front-load washing machines. It secures the door during operation, preventing leaks and ensuring the washer functions correctly. A faulty d...
This is an actuator switch to trigger bleach, detergent, or fabric softener housings to be dispensed into the tub of your washing machine. If your detergent cups are not dispensing, you may need to re...
Upgrading your laundry room? We can help you save space effortlessly with our Whirlpool Long Vent Dryer Stack Kit. Designed specifically for certain Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Ing...
$80.87
In Stock
Questions And Answers for WFW94HEXR2
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jaime
January 12, 2025
Sounds like the motor starts running but doesn’t do anything
For model number WFW94HEXR2
Hi Jaime, thank you for reaching out. We would suggest checking the rotor and stator for any damage first. If they are fine, the issue could be with the motor control board, part number PS11753928. You may need to replace it to fix the issue. We hope this sorts out your problem!
My washer is not getting any water and the drum doesn't mive
For model number WFW94HEXR2
Hello David, thank you for getting in touch. Most washing machines will not spin unless filled with water. Make sure both hot and cold water taps connected to the washing machine are fully open. Also, check the water pressure, low water pressure can prevent the machine from filling. A faulty water inlet valve, part number PS11752082, can also prevent the washer from filling. We hope this helps.
Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.
Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.
The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machine requires brute force.
Once the hose was out I found some bra under wires which is what probably punctured the hose.
Removed the front filter and found a bunch of nails.
Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Using the Torx Screwdriver, we removed the door from the unit. Then we removed all of the screws on the inside of the washer door. After that we flipped it over and opened it up exposing the inside. We couldn't separate them entirely because there was a screw under the latch piece that we couldn't figure out how to get to. However with all the screws out on the inside of the door, we did have enough room to open it up and access the place cover that holds the hinges in. Once we accessed that we removed the roller tips from the old unit and placed them on the new one. Then we reversed the process. With a couple screws in we realized we had put the hinge in reversed from what it needed to be, so we reopened it and switched it around. Then completed replacing all the screws and reattached it to the washer. It opens and closes perfectly and we saved a couple hundred dollars for sure, as the quote to come out had been a $150 trip charge.
