All Installation Instructions for Whirlpool Washer WFW9200SQ02

Broken hinge

Removed screws around door couple around hinge

Parts Used:

Washing Machine Door Hinge

Kevin from JACKSONVILLE, FL
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Bellow pierced

1. Remove bottom panel (3 screws below). 2. Remove top panel (3 screws back). 3. Remove detergent dispenser (remove T screw in front.) 4. Carefully remove control panel is plastic so be careful not to break it. 5. Pull broken bellow from front and spring loaded clamp will come lose. 6. Push away bellow. 7. Remove cables from door lock. 8. Remove front panel screws (4 - 2 on top and 2 in bottom). 9. Unscrew bellow's clamp with flat screw driver or not driver. 10. Remove worn bellow. 11. Bellow has notch on top (Use as reference to replace. 11. Clean all surfaces. 12. Install new bellow to drum. 13. Screw clamp over of bellow not too tight. Don't want to break the seat. 14. Replace all in the reverse order and for the front of the bellow refer to my previous article (story) on front latch replacement.

Parts Used:

Washer Door Bellow

Alexander from Miami, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Socket set

4 of 8 people found this instruction helpful.

Was this instruction helpful to you?

wont pump the water out

Had the old pump out - 1 screw and two hose clamp to unhook and an electrical wire to pull out - couldnt been any easier - when new one came took 5 mins to install - did a load to make sure pump worked before put it all back together

Parts Used:

Drain Pump Kit

Paul from Corning, NY
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

3 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Water filling up in drum when not in use

Took top off with nut driver, disconnected 2 wires , removed one screw holding inlet value. Then I reversed the procedure putting new one on. Maybe 20 min. Of course unplug power and turn off water supplies before starting the job.

Parts Used:

Washer Water Inlet Valve

Don from Oceana, WV
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Baffle broke off due to drying very heavy garments.

Lined the new one up with one hand;(cold beer in the other), snapped it to place, finished.

Parts Used:

Washer Baffle

Lionel from HOCKLEY, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Detergent draw was cracked.

Took draw out of machine removed faceplate,to get at the two screws that hold the face plate bracket on , removed the two screws that hold the bracket on.installed the bracket on the new draw and slide it in the slot and your done.

Parts Used:

Handle Fixation Bracket

Detergent Drawer

timothy from PORTLAND, ME
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Washer wouldn't drain

Easily. 4 Screws. 2 Clamps.

Parts Used:

Drain Pump Kit

Jeff from Barrington, RI
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Broken baffle in washer.

Inserted new baffle in washer and slide in place.

Parts Used:

Washer Baffle

Benjamin from N WILKESBORO, NC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Washer shook and made noise during spin cycle.

Shocks are the #1 recommendation for this problem, but they were not the solution. The problem turned out to be broken weld in the stainless tub. Three of the shocks can be replaced from the front, the one under the motor can only be accessed from the back of the machine, which means it has to be pulled out away from the wall. Taking the old ones out is kind of a pain, they don't twist off easily and there is little room to use tool. Putting the new ones in is easy, they just twist into place.

Parts Used:

Shock Absorber

Homer from Windham, NH
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

front door leaking

2 clamps and its off, problem is if you have average size hands you will struggle in getting the back clamp on and off.

Parts Used:

Washer Door Bellow

jim from winchester, VA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

3 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Tear in door seal

First I removed the retainer ring that holds the outside bellows on the frame of the front washer.
I then pushed the bellows inside of the drum of the washing machine in-order to get to the clamp that holds the bellows on the inside of the drum. To pull the clump I had to use a stubby screwdriver and socket drive to loosen the clamp. Once the clamp is loosen I was able to pull the bellows off, of the drum and out of the washing machine. Installation was the reverse of removal.

Parts Used:

Washer Door Bellow

sean from Palm Coast, FL
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set

4 of 9 people found this instruction helpful.

Was this instruction helpful to you?

The door bellows had a cut in it

I purchased a new bellows from this site I followed their instructions. Just tricky getting the inner clamp on aligned and tightened.

Parts Used:

Washer Door Bellow

Arthur from MORGANTOWN, PA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Ripped bellowspul

Pull spring wire on front. Remove large hose lamp at tub. Reinstall in reverse order.

Parts Used:

Washer Door Bellow

WILLIAM from REPUBLIC, MO
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Screw drivers

2 of 3 people found this instruction helpful.

Was this instruction helpful to you?

The washer machine didn’t start the cycle. Had a weird sound. Then f 30 was ther error code. With research internet it was easy to know about the motor dispenser problem

I did follow step by step your YouTube video. I’m a woman. There was nothing heavy in the process. You have to be careful that’s it. Thank you for the instructions. I fixed it with the YouTube tutorial you provided. Really nice from you people.

Parts Used: