This is the main seal between the front bulkhead and the outer tub. If the washer is leaking, the door boot may have a tear in it. Overloading the washer is the most common cause for a torn door boot
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. It has two ports for water to pass through: a large one, and a s...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the oute...
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
Water inlet valve controls the water flow into the washer.
Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW...
If your washer door won’t close or lock, or your machine won’t start, this door latch might be the issue. It’s the part that keeps the door shut tight during the cycle and makes sure everything runs s...
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is...
This is the replacement tub baffle for your washer. It is made of black plastic and is approximately 13 inches by 2 inches. This part is sold individually and is an OEM part sourced directly from the ...
$80.56
In Stock
Questions And Answers for WFW9150WW01
Ask our experts a question about this model and we'll get back to you as soon as possible!
8 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sal
December 21, 2019
Can i return it back if it’s not the right part?
For model number WFW9150WW01
Hello Sal and thanks for writing.
Yes, you can return any part that has not been installed and it is in its original packaging within 30 days of purchase.
We do carry related parts for units just like yours. For example, part number PS11746261 Good luck with your repair.
It start to wash then quits. Have to put it on rinse spin cycle to get soap out. So whats wrong is it the control board or control panel?
For model number WFW9150WW01
Hello JD and thanks for writing.
It certainly sounds like a faulty Central control board PS11755970 check the part and replace it if needed. We hope this helps. Please contact us anytime.
2 peoplefound this helpful.
Was this helpful?
Thank you for voting!
Dale
February 17, 2025
why does my washer peep during the rinse cycle and stops all operations
For model number WFW9150WW01
Hello Dale, Thank you for the inquiry. Beeping during the rinse cycle and stopping operations normally indicates an issue with drainage. We suggest checking for a clogged drain hose, drain filter or drain pump. This can also indicate a faulty Drain Pump if there is no blockage. We hope this helps!
What do I need to replace on my washer if when it spins there is a lot of noise?
For model number WFW9150WW01
Hello Heather, thank you for reaching out. We would recommend checking the drum bearing to fix the issue. The drum bearing does not come separately. You may need to replace the outer tub, part number PS12578762, to fix the issue. We hope this helps!
On Whirlpool front load washer ,bad vibration on spin cycle. Of 3 pistons to absorb vibration one (left rear)has more up and down motion than others. Does this indicate a bad piston that should be replaced? Is part no. PS11723173?
thanks,bruce
For model number WFW9150WW01
Hello Bruce, thank you for contacting us. The issue is most probably related to the shock absorber, part number PS11723173, which is oscillating with more amplitude than the others and replacing it is the most likely solution. We would also recommend checking the suspension spring set, part number PS993023. This set supports the outer tub and keeps the tub stable during unbalanced loads. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
