WFW8300SW02 Whirlpool Washer - Instructions

Unplug Unit, remove lower cover screws with screwdriver that has 1/4 drive at end, put 2 gallon bucket at strainer remove water. Remove inlet hose clamp and outlet hose clamp, disconnect pump motor wiring plug, aggressive push to RIGHT popped right out. put a dab of Vaseline on new units rubber base slide back in reverse order. Plugged in check for leaks put back together, Repair took less than 15 minutes, working great! WHAT I FOUND IN STRAINER: LEGO'S-CHANGE-PAPER CLIPS, enough things to destroy the impeller !

Had my appliance man do it. It was the first one he had ever done in 20 years of working on Whirlpool. It was quick. The parts I received from you were cheaper than his supplier. Needless to say that made me very happy!

Just follow the repair video and you are good to go. Very easy my 16yr old did it.

First, I watched the video again just to make sure I had a firm grasp of the task ahead. I gathered up the tools and proceeded to begin. First obstacle: getting the washer tilted back enough to put the blocks under the front feet. The washer was sitting inside a square water pan with a drain connected directly under the middle of the washer. Therefore, the water pan did not move and I could only get the washer moved out far enough to 'barely' put the blocks underneath. Second obstacle: a clump of hair had gathered at the bottom portion of the door unnoticed and caused a slow leak from the bellows. This leak dripped down and rusted out two of the three screws. I had to use a socket set to get the screws out. Third obstacle: getting the pump removed from the bottom of the washer. With the drip, the pump had stuck to the bottom of the washer. Trying hard not to get cut on the sheet metal bottom, I pushed and pushed and pulled until finally the pump let loose. From that point on..smooth sailing just like the video. Washer fixed!

I had to replace the bellow to the washer because I discovered the leak was from the door and bellow area, only problem I really had..... was installing the bellow on the outer drum, I applied a coat of hand soap to make it easier to secure in place.

removed retaining ring on front gasket, pulled gasket back, took out door lock latch, unhooked wires, then reversed method to replace.

Took of the panel, unscrewed the old drain, screwed the new drain in. Very very simple to do! The first part I received leaked, I called customer service and they gave me a refund and express shipped a new part - no questions asked. Very good customer service!

I found a YouTube video that showed how to totally dismantle the machine. I removed the top ( easy 3 screws). Removed the bottom access panel (easy). Removed the control panel (1 Torx screw and rather tricky to unsnap). Removed the door and hinge (2 Torx screws). Removed the below retaining band (easy). Disconnected the bellow at the front panel then removed the door lock mechanism (easy). Removed the front panel (easy). Removed the bellow clamp on basket side (screwdriver hose clamp type, a little tricky but not too bad). Installed the new bellow paying close attention to the drain holes being centered on the bottom. Assembled all parts in reverse order. The really tricky part was the bellow clamp on the front panel. Patients prevailed.

After getting dress that wife denies closing in door out the repair wasant to hard. There are 3 or 4 phillips screws in back that holds top on that have to be taken out and the kick plate cover on bottom just snaps off but the rest is covered very well by other discriptions.(by the way the dress had to be thrown away so not only did i get to by bellow but a new dress also and the bellow was cheaper)

Just went by instructions provided by parts web site

The new drawer came and I took out the the detergent despensor piece from the old drawer and placed it in the new drawer and put the new drawer back into the washer. Now the front of the washer is complete. Good as new. Part also arrived in a timely manor too. Very pleased

It was real easy. I disconnected the wiring as shown in the video. I took the clamps off the drain pump , once off I slid the old drain pump off. I slid the new pump on , attached the hoses with the clamp provided and connected the wiring. Just follow the video and you will find it to be very easy! Thanks Parts Select for saving me money

other than needing a new type of screw driver (not philips or flat head, but rather a starfish looking thing), the replacement was simple. took 5 minutes (after finding the correct driver)

Thank You so much for the other stories folks wrote on here! We were getting an F21 code on a regular basis. After finding a necklace and about $2.50 in change in the filter tray we found the problem. Over time I thought the washer was getting louder but it was so gradule that we really did not realize it.I had read other posts on here and ordered a new pump. After taking out 3 screws and 2 clamps the pump came right out and went in just as easy. Less than 15 minutes and we were back in business with a wisper quiet washing machine,Thanks Again everyone, Mike D.

I drained the water out of the pump area. Then took off all clamps and holding brackets. Next I pulled off the quick connect power plug. Then I put new pump in the way I took old pump out. The hardest part was unscrewing the bracket from underneath the washer. Cloth washer working fine.