WFG366LVB0 Whirlpool Range - Instructions

I didn't. Don't know how to get to light bulb to change it for this specific model

Turned off power to range. Removed the lower panel that was secured by two screws, as well as the metal cover beneath it also secured by screws.. Removed the two screws securing the igniter, and pulled apart the black tubing that secured the igniter. (I had to pull hard to get it apart). Plug the new end into that same black tubing. screw in the two screws to secure the new igniter (this is tricky because one screw is hard to reach) I laid something in the base to cover the holes so I wouldn't lose a screw if it dropped. Screw metal panel back in, followed by the lower oven panel.

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

Just took the bottom cover off the bottom of the stove, pulled the old igniter and put the new one on.

This did not solve my problem.
What do I need to do next?

took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one

Remove vent trim from oven and set oven glass to the side. Next remove handle from vent trim (two screws). Next place handle on new vent trim. Place glass in place, (it is held in place by bottom of oven door and vent trim). next place side trim in place and place that side of the vent trim and loosely tighten screw holding trim into place at top of the glass. Next place the other trim into place under the vent trim and tighten the screws on both sides.

I had problem with the oven of the stove since the beginning. It wa difficult to start. Later, it stoped working. The technician told m that the gas valve regulator was the problem. That was the reason I decided to buy a new one. After installing it, however, the problem continues. The ignition starts, but the gas does not go thru. It seems the signal does not go to the valve to open the gas.

the hardest part was moving stove to trplace part

Removed two gas lines at the safety valve. Removed the four mounting screws and disconnected the three wires. Re-assembled in reverse order of dis-assembly. This was an easy diagnosis and repair/replacement. The PartSelect website is very easy to use if you have the model number and I like the diagrams to be sure the part is correct.

Took knob off ordered new one put it in place

Removed drawer, after removing the 50# of junk in the drawer, Used screw driver to remove screw that holds glide to drawer and then place new part into place put screw into hole and tightened screw. Replaced drawer and told wife not to put 50# of junk back into the drawer.

Removed the bottom pan and heat shield plate, removed the drawer to get to the igniter disconnect the one wire from it and removed it and just repeated the same process backwards to put the new one in. All under 15 mins

As the 2 screws in the front of the flame spreader didn't screw into anything , and made getting the flame spreader very difficult to remove, once I got the flame spreader out , I did cut off the screws so future install & removal would be easy. I had to hacksaw the screws off , as the screws are otherwise impossible to remove. The screws were damaging the oven metal sheet work during first removal ! Otherwise the new bake ignitor install would have been a very quick 20 minutes. Also I watched u-tube bake ignitor install & oven door remove videos, which were extremely helpful.

Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.