All Installation Instructions for Whirlpool Range WFG361LVD3

Outer glass of the oven door is broken.

I took out the two screws that held the oven handle in place inserted the glass in the door and replaced the two screw!!! That easy!

Parts Used:

Range Exterior Door Glass

Ernestine from baltimore, MD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

11 of 20 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

the part that fits on the stem to turn the knob had broken. I tried to tape it together, but that did not work.

since it was the control knob, all I had to do was to push it right onto the stem, and it was finished. Using the web site to find the correct item was very easy.

Parts Used:

Range Control Knob

Charlaine from Romeoville, IL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

9 of 14 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

scratches and paint detoriation on bottom part of oven

Remove 2 screws holding oven bottom in place.Lift out the plate and replace with new plate. The hardest part of the replacement was lining up the screw holes. By the way i have never received such great service from any internet company as Part Select. I ordered the part on a Monday and the part was at my home the NEXT DAY and installed that evening.

Parts Used:

Range Interior Bottom Oven Panel

Peter from Galloway, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven would not ignite for BAKE. Gas would come on and igniter would "click" twice, then when burner did not light up gas went off.

Bought new igniter.
Pulled stove from wall and turned off gas and disconnected power cord.
Removed oven racks.
Removed oven floor.
Removed heat shield/dissipater thing.
Removed 2 screws holding igniter to gas burner tube.
Disconnected the wire (this was harder than expected because igniter had only a few inches slack in the wires), took off back to try to find better access to wires, no help there, door was not easily removable so difficult to reach in with 2 hands to pull wires apart, eventually I got it.
Connected new wires.
Replaced igniter to feeder tube with 2 screws.
Plugged back in, turned gas back on and tested.
Reassembled heat shield thing, oven floor, racks.
Done.

Parts Used:

Range Bake Igniter

David from N RIDGEVILLE, OH
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Both right and left side trims were broken.

Ordered both parts using the excellent breakdown illustrations of the door. Received the parts along with video instructions on how to repair.

Parts Used:

Side Trim

Side Trim - Right Hand Side

A D from HOUSTON, TX
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

6 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

very intermittent oven won't light. Can hear gas and spark but won't light when spark isn't at ignitor tip (shorting somewhere before the tip)

Remove;
Bottom drawer- pull open and lift up slightly when fully open then pull the drawer the rest of the way out.
Unplug ignitor terminal- there is a small tang inside the terminal end that needed pressed out of the small hole of the ignitor, with a pick.
Oven racks.
Oven bottom- 2 long phillips screws at the back. lift the back up 1st then the front comes up and out.
Burner diffuser- 2 small phlilips at front (they only prevent the diffuser from sliding, they don't screw into anything). slide diffuser forward out of the notch then lift the front up. pull rear tabs out of the notches to completely remove.
Ignitor- two 8mm (5/16) bolts holding ignitor to burner. pull ignitor out of guide holes.
Reverse to install new ignitor.

Parts Used:

Range Bake Igniter

Mark from COLUMBUS, OH
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

broken bottom drawer glide and missing rivet on drawer front panel

Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.

Parts Used:

Range Rear Drawer Glide

Rivet, Push (White)

David from Fairborn, OH
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

6 of 8 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Door bottom trim piece was rusty

Remove three screws, slid old trim piece off door. Slid new trim in place. Used ice pick to align screw holes and replaced screws. Total time about 15 minutes. Tip: used a bead of silicone sealer on the new trim strip to prevent moisture from causing new strip to rust.

Parts Used:

Range Trim Lower (Biscuit)

Dennis from Dunnellon, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven bottom heavily corroded; difficult to clean.

Removed two screws holding the bottom in, pulled out old bottom, inserted new bottom, replaced screws and tightened them. Total time less than five minutes.

Parts Used:

Range Interior Bottom Oven Panel

Edward from Sinks Grove, WV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Knobs broke

Replaced broken knobs. No tools needed.

Parts Used:

Range Control Knob

Marie from ELLIJAY, GA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

5 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

light bulb in water ice freezer door went bad

I didn't. Don't know how to get to light bulb to change it for this specific model

Parts Used:

Light Bulb - 40W

Carl from RIVERSIDE, CA
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
Tools:
Screw drivers

7 of 13 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven sensor was not regulating heat set for oven

Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too

Parts Used:

Oven Sensor

Linda from SAINT CLOUD, MN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

I broke a piece of the trim and had to replace it

took the handle off, replaces the side trim piece and replaced the handle. Very simple!

Parts Used:

Side Trim - Right Hand Side

Gregg from SOUTH BEND, IN
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

4 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven clicked, but would not ignite in gas range

Turned off power to range. Removed the lower panel that was secured by two screws, as well as the metal cover beneath it also secured by screws.. Removed the two screws securing the igniter, and pulled apart the black tubing that secured the igniter. (I had to pull hard to get it apart). Plug the new end into that same black tubing. screw in the two screws to secure the new igniter (this is tricky because one screw is hard to reach) I laid something in the base to cover the holes so I wouldn't lose a screw if it dropped. Screw metal panel back in, followed by the lower oven panel.

Parts Used:

Range Bake Igniter