Models > WFC310S0EB2 > Instructions

WFC310S0EB2 Whirlpool Range - Instructions

All Instructions for the WFC310S0EB2
31 - 45 of 158
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Element wasn't being controlled by the switch it would stay on high
Ordered a new switch and replaced the old one with it.
Parts Used:
Surface Burner Element Switch, Large Burner
  • George from FRANKLIN, KY
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
6 of 7 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The burner would not shut off.
Pulled the dial off, unscrew two screws. Pull the switch out from the back. Disconnect the wires from the old switch and connect to the new switch one by one. Set the new switch in place. Sctew the two screws in to hold the switch in place. Push on the dial.
Parts Used:
Infinite Switch - 6 Inch
  • Richard from CONCORD, NH
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
6 of 8 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace aged Drip bowls
Lift and remove heat elements
Lift and remove Drip bowls

Replace Drip bowls and heat elements
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • ROBERT E. from GLENDALE, CA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
5 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven sensor was not regulating heat set for oven
Following your installation, the old part came out easily, with new part installing easily., oven heat is being regulated properly..with range pulled out for part replacement, got that area cleaned too
Parts Used:
Oven Sensor
  • Linda from SAINT CLOUD, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Generic drip bowls in the stores did not fit
Very easy remove the burner and instill the drip bowls
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Elaine from BROAD BROOK, CT
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
light bulb in water ice freezer door went bad
I didn't. Don't know how to get to light bulb to change it for this specific model
Parts Used:
Light Bulb - 40W
  • Carl from RIVERSIDE, CA
  • Difficulty Level:
    Very Difficult
  • Total Repair Time:
    More than 2 hours
  • Tools:
    Screw drivers
7 of 13 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I broke a piece of the trim and had to replace it
took the handle off, replaces the side trim piece and replaced the handle. Very simple!
Parts Used:
Side Trim - Right Hand Side
  • Gregg from SOUTH BEND, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
2nd 8 inch burner switch in a little over a year to not always hold selected tempurature.
As a former appliance repairman, the installation went just like the repair instruction video.
Just use care not to scratch anything and clean behind the appliance and cabinet walls, etc. It's worth a hug and a piece of pie!
Parts Used:
Surface Burner Element Switch, Large Burner
  • LELAND from HERMISTON, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
4 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
My drawer did not line up
Putting the drawer glides on was easy. My range drawer did not have any glides on so my drawer would fall out. The drawer glides popped right on the drawer. The glides for the track were easy to screw into the body of the range. I had to bend the tracks up a little on each side with a pair of pliers. One glide would go onto the track and the other one would go on top of the track. After bending them a little I was able to push them onto the track.at the same time.
Parts Used:
Drawer Glide Kit - Black
  • Angel from SN BERNRDNO, CA
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
temp sensor went oven not heating
the hardest part was moving stove to trplace part
Parts Used:
Oven Sensor
  • patrick from HUGHESTOWN, PA
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
bottom piece of range rusty
took old one off and installed new one used electrical tape to hold glass from sliding.Unscrewed moulding and installed new one
Parts Used:
Range Trim Lower (White)
  • Bruno from LE ROY, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
4 of 5 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven Temp inaccurate
I watched the repair video on this site and another on YouTube before I started. The rear panel has a different shape and two additional screws on the bottom edge. The power clip was easy to manipulate.
This was an easy fix for a seventy year-old like me!
Parts Used:
Oven Sensor
  • David from BURNSVILLE, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Bowls were rusted through
Really simple just pull them out and stick them back in
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch Light Bulb - 40W
  • Kevin from SPENCER, NE
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The oven light shorted out causing the safety thermostat to blow.
Replaced the safety thermostat and disconnected the oven light.
Works great again...without the light
Parts Used:
Range Safety Thermostat
  • Joseph K from PAHRUMP, NV
  • Difficulty Level:
    Very Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
4 of 6 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oven stopped heating, error message stated heating element
Very easy. Pulled the stove away from the wall. Used a screw driver to remove the two nuts to release the heat sensor, disconnected the wire, removed the sensor. Inserted the new sensor, plugged back into the circuit. put the two nuts back.
Beware, if the first time you put the oven on, if the error message comes back up (mine did) push the cancel/off button, wait a few minutes, put oven back on. System probably needed to reset. Mine worked perfectly after.
Parts Used:
Oven Sensor
  • Lana from WATERVILLE, ME
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
3 of 3 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WFC310S0EB2
31 - 45 of 158
Back to Top