Models > WFC150M0JS4 > Instructions

WFC150M0JS4 Whirlpool Range - Instructions

All Instructions for the WFC150M0JS4
106 - 120 of 127
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
bowls had burnt on food
replaced them
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • David from Saranac Lake, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
E-2 F-3 codes..Oven inop w/trying to bake.Beeps @ start attempt.
Contrary to instructions(go thru front of oven) I had to pull out the range, remove two (2) screws from back chassis. At this point you pull out the connector, snap in new, reverse proceedure. Very simple. Hardest part is cleaning up debris generated by moving range.
Parts Used:
Oven Sensor
  • Dave from Titusville, FL
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
the dial would not work unless the special screws, which are extra short, are utilized.
since I only had one of two screws, i installed with just the one. it would not work at all using a slightly longer screw, which is very odd.
Parts Used:
Surface Burner Element Switch, Large Burner
  • Bruce E from Oxford, MS
  • Difficulty Level:
    Easy
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Nutdriver, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
intermittant power to "burner" eye
due to the cooktop age, part was not an exact duplicate. I had to drill new holes in the stainless steel for mounting and ground wire. I used a lot of kitchen matches to heat the shrink tubes over the twist connectors. I should have gotten a heat gun or torch.
Parts Used:
Range Receptacle Kit
  • don from Orange, TX
  • Difficulty Level:
    A Bit Difficult
  • Total Repair Time:
    30 - 60 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
arcing within the cook top electric heat element and the receptacle.
Cut, splice and heat shrink.
Parts Used:
Range Receptacle Kit
  • Paul from Levittown, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
Replace bowls
Removed old bowls and replaced with new ones. Easy. Piece of cake. Perfect fit.thanks.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Judy from Indianapolis, IN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
old bowls could not be cleaned. These new bowls make the stove look great
Removed old bowls and replaced with the new bowls. Also, thanks for your help with the rang knobs. You did not have the replacement knobs for my range but you gave me help in where I might get them. With the new bowls and knobs the range looks like new. Thanks again for all your help.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Gerald from Rochester, NY
  • Difficulty Level:
    Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Old Drip Bowls
Lifted out the old ones and inserted the new ones and my range top looks brand new now!
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • James from Edgewater, MD
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
none
I pulled out the burners, cleaned up the crumbled drip pans ,installed the new drip pans, pluged in the burners and was finished in about 3 minutes. I will order again from you. Thank you.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Dennis from Viroqua, WI
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
my drip bowls were old an I was unable to clean them
I took the old drip pans out and replace them with the new ones. Now my stove looks brand new. These were a perfect fit.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Anne Marie from Albany, NY
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Old drip bowls, tried prepackaged from box stores
After putting up with ill fitting generic versions of our drip bowls, we smartend up and ordered correct parts. They went in super easy, perfect fit and the heating element is now perfectly level. Who knew that following the manufactors recommendations to buy correct parts would make such a difference? Well we know now! Thank you. The parts were shipped almost immediately and delivered as promised.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Christine from Phoenix, OR
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
Drip pans missing
placed element in drip pan and plugged in. .Fit perfectly.I am very pleased with the product and service.
Parts Used:
Drip Bowl - 6 Inch Drip Bowl - 8 Inch
  • Michele from Walnut, CA
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
Was this instruction helpful to you?
Thank you for voting!
broken burner switch
Easy as pie! Thank you for the illustration to help us pick out the correct part.
Parts Used:
Infinite Switch - 6 Inch
  • Coral from Duluth, MN
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    Less than 15 mins
  • Tools:
    Screw drivers
Was this instruction helpful to you?
Thank you for voting!
The large burner sometimes stayed on high too long, burning food
My first approach was to try to find some help on the internet - Y-Tube or whatever. When I could not find anything, I was on my own. My first thought was that the best and easiest access to the switch was to somehow remove the top section of the range which held the switch. I was trying to avoid having to pull the range from the wall and cabinets. But not finding any way to do that, I then pulled the range from the wall, and removed the back panel (8 screws), which gave me easy access. Once that was done, the replacement went smoothly and quickly. So if replacing any switches on this range, FIRST pull it from the wall and THEN remove the back panel, and the rest is a piece of cake!
Parts Used:
Surface Burner Element Switch, Large Burner
  • Harry from Seminole, FL
  • Difficulty Level:
    Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
could not control temp on burner
Took appro 8 screws out of back panel, 2 screws holding switch, and pulled out switch, unhooked wires and reinstalled wires on new switch. Had to snap off stem with needle nose pliers which is simple and put everything back in place in reverse order!
Parts Used:
Surface Burner Element Switch, Large Burner
  • Ernie from Cameron, MO
  • Difficulty Level:
    Really Easy
  • Total Repair Time:
    15 - 30 mins
  • Tools:
    Pliers
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the WFC150M0JS4
106 - 120 of 127
Back to Top