All Installation Instructions for Whirlpool Range WFC150M0EW4

Worn/Bulb Socket

It was alittle difficult at 1st to remove the clips that held in the socket. But once out everything went smoothly.

Parts Used:

SOCKT-LITE

JOSEPH from COON RAPIDS, MN
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The Range took forever to achieve the proper heating temperature with an inability to maintain a steady heat

I removed the bottom drawer,unplugged the Range and pulled it out to expose the rear cover panel. Using a nut driver (a screw driver can be used), I removed the rear panel to expose the Thermal fuse located almost dead center in the back of the Range. Unplug the two wires and loosen the screw holding it in position. Replace the thermal fuse, plug the two wires into the new part and replace the rear cover panel. Return the Range to its original position and plug it in. The job is done in less than 30 minutes.

Parts Used:

Safety Thermostat

Robert from Mifflinburg, PA
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

My drip bowls were scorched and discolored and difficult to clean

I removed each surface coil burner from its receptacle; removed the old drip bowls and replaced with the new ones; my stove looks good as new.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Claudia from Milwaukee, WI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Front glass shattered, side trim broke and lower trim bent beyond repair

Followed the YouTube video and did it the correct way they showed. Note: side trim goes under the glass.

Parts Used:

Outer Door Glass - White

Trim, Lower (White)

Daniel from CEDAR SPRINGS, MI
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Light would not light

Pop old one out and new one in

Parts Used:

SOCKT-LITE

Frank from LEBANON, VA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven temperature was 50 degrees off

Unplugged stove.
Pulled stove out.
Unscrewed screws and removed cover.
Removed & replaced sensor.
Reinstalled cover & screws.
Plugged in stove and pushed back in.
Only problem was when I pulled stove out, lid opened and disconnected the gas line to a burner.

Parts Used:

Oven Sensor

Gregory from BRIDGEBORO, GA
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

burnt out drip pans

I had been putting off this repair for months! I finally sat down to explore ordering the parts. It was so easy - I wish I did it a long time ago. When the parts arrived, they were exactly what I needed.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Barbara from KAMUELA, AL
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Replace burner drip pan

Removed electric coil replaced pan and reinstalled coil. Part fit just right and no problem.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Ray from Council Bluffrs, IA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven light not working

replaced light socket but did not repair problem. must have burned the motherboard.

pleased with service from your company.

Parts Used:

SOCKT-LITE

Richard from Gaylord, MI
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

reflecter/drip pans wrong size

Ordered acording to range model & such. Had ben unsucksessful gettin the right size thru the years & finally got the correct ones.

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Dann from Glendale, AZ
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Eroding burner drip bowls

Removed old drip bowls and installed new, which, thanks to your efficiency, were a perfect replacement

Parts Used:

Drip Bowl - 6 Inch

Drip Bowl - 8 Inch

Edward from Hamilton, OH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 3 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Bad Receptacle

I had a receptacle melt in front of my eyes. I few questions later PartSelect.com showed me the part I needed and was checking out in less than 10minutes. Part arrived 3 days later and 20 minutes after that it was installed. I'm Amazing!!! No, PartSelect.com is AMAZING!

Parts Used:

Receptacle Kit

TROY from YPSILANTI, MI
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 6 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven gets too hot,if set at 350 it heats to 550. Changed the sensor and was not the problem.

Took off the screws on the back of the stove and took out the sensor, and put in the new one.

Parts Used:

Oven Sensor

Joanne from Negaunee, MI
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

0 of 1 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Terminal block arc'ed because a wire had become loose.

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Parts Used: