This part helps keep your front-load washer safe and working properly. It locks the door during cycles so it doesn’t open unexpectedly, and it also tells the washer when the door is shut so it can sta...
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
Introducing the Samsung Washer Shock Damper Front, a vital component for optimal washer performance. This part maintains the stability of your washer, helping minimize vibration and noise during opera...
Introducing the Hex Head Bolt, a vital component designed to keep your Samsung, Kenmore, or Maytag washer functioning at its best. Manufactured with strict quality controls, this part ensures you rece...
Also known as a bellow. This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
Revive the wide array of your appliances including your Samsung Refrigerator, Samsung Dryer, Samsung Washer, and even your Samsung Dishwasher with the Tapping Screw, a crucial component engineered by ...
Optimize your Samsung, Maytag, or Kenmore washer's performance with the Drain Pump Assembly - 120V 60Hz. This high-quality unit directly replaces the original drain pump, ensuring efficient and smooth...
No Longer Available
Questions And Answers for WF219ANBXAA
Be the first to ask our experts a question about this model!
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
1. remove the three screws from the top backside of the top panel 2. push the top panel to the rear 1/8 to 1/4 inch 3. lift/rotate top panel from rear to front, set aside. 4. remove the three wire connectors from latch. 5. use #15 Torx to remove the three screws from the latch. 6. remove and replace part using top opening. 7. reverse order to finish.
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the back of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that. (there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that. You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble. (Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
replaced door latch but door would not close had to remove latch assembly and reset the latch in the latch assembly. To reset latch in latch assembly you remove the black plastic only on latch assembly then press the spring down with thumb move the black plastic catch back to the latch position. when you remove the black plastic there is four metal switchs and one spring that you have to pay attention too so remove very carefully.
