WF206BNWXAA Samsung Washer - Overview
Sections of the WF206BNWXAA
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Washer Door Lock Latch
PartSelect #: PS11745016
Manufacturer #: WP8182634
This part helps keep your front-load washer safe and working properly. It locks the door during cycles so it doesn’t open unexpectedly, and it also tells the washer when the door is shut so it can sta...
$156.03
In Stock
Hex Head Bolt
PartSelect #: PS4205366
Manufacturer #: DC60-40137A
Introducing the Hex Head Bolt, a vital component designed to keep your Samsung, Kenmore, or Maytag washer functioning at its best. Manufactured with strict quality controls, this part ensures you rece...
$11.95
In Stock
Inlet Hose - 5 FT
PartSelect #: PS11746820
Manufacturer #: WP89503
This hose can handle hot or cold water and is five feet long.
$27.29
In Stock
Drain Pump Assembly - 120V 60Hz
PartSelect #: PS4204638
Manufacturer #: DC31-00054A
Optimize your Samsung, Maytag, or Kenmore washer's performance with the Drain Pump Assembly - 120V 60Hz. This high-quality unit directly replaces the original drain pump, ensuring efficient and smooth...
No Longer Available
Washer Tub Gasket Seal
PartSelect #: PS4213806
Manufacturer #: DC69-00804A
Upgrade your domestic laundry routine with our Washer Tub Gasket/Seal. Designed by leading brands, Samsung and Maytag, this product is designed for maximum efficiency and durability. Guaranteed to fit...
$35.95
In Stock
Washer Door Diaphragm
PartSelect #: PS4210920
Manufacturer #: DC64-00802A
Have you noticed your Samsung washer is not operating as efficiently as it used to? Or Perhaps you've spotted a leak? It's likely because there is a tear or wear in your door boot seal-gasket. Our r...
$161.32
In Stock
Door Glass
PartSelect #: PS4210731
Manufacturer #: DC64-00504C
Is your Samsung washing machine door glass broken or cracked? We've got just what you need to fix that problem. Introducing our Samsung Washer Door Glass ? a reliable, high-quality replacement part cr...
$155.15
In Stock
Oil Seal
PartSelect #: PS4208713
Manufacturer #: DC62-00223A
Introducing an integral element for your washing machine maintenance, Samsung's oil seal. This essential component is expertly designed to be pressed into the rear drum of your washer, thereby providi...
$44.95
In Stock
Drain Pump
PartSelect #: PS4216974
Manufacturer #: DC96-01414A
Everything you need to keep your Samsung or Maytag washer working properly can be found right here. The Drain Pump is essential in ensuring your washer operates efficiently, smoothly channeling water ...
$192.03
In Stock
Water Hose
PartSelect #: PS4212730
Manufacturer #: DC67-00089A
Introducing the Samsung,Kenmore Washer's essential component - the Hose - Water. This high-quality component is known for its enduring performance and its primary function is to ensure efficient flow ...
$26.95
In Stock
Questions And Answers for WF206BNWXAA
We're sorry, but our Q&A experts are temporarily unavailable.
Please check back later if you still haven't found the answer you need.
Common Symptoms of the WF206BNWXAA
[Viewing 6 of 6]Lid or door won’t close
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Locking Issues
Fixed by
these parts
these parts
Show All
Door latch failure
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
front load washer latch replacement
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. reverse order to finish.
Parts Used:
-
James from Vilonia, AR
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
196 of 240 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Door lock was in the locked position and door could not close
I bought a new door lock for 132 dollars (item number PS2037196).
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the back of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Ultimately you have to get to the inside of the machine where the door lock is located in order to see if you will need this door lock that I bought.
DISCONNECT POWER FROM MACHINE.
First take off the top by taking off the 2 screws on the back of the machine.
Second take off the control panel, I believe there are about 5 or 6 screws for that.
(there's also a screw when you open up the detergent compartment on the bottom left- also, a lever must be pushed in order for the compartment to come off- it MUST be taken off).
Third unscrew the top of the front white plate.. there should be a 5 or 6 screws for that.
You don't need to take off the entire front plate.
Finally unscrew 3 screws that hold the door lock in place .. make sure your hands is in the machine- the back of door lock to catch the lock when you're on the last screw.
Gently take out the door lock from the side with the cables attached by holding the white metal door open (it bends).
Try to pull on the bottom of the door lock (its a manual release). If it doesn't release you need to buy a new door lock like I did... if it does release then you don't need a door lock and just reassemble.
(Note: You can also try plugging in the machine and THEN pulling down on the manual release. When I tried this the door lock just vibrated and nothing happened so I bought a new door lock.)
If you have the new door lock continue here:
Take out all 3 cables on the old door lock by pressing on the corresponding clips.
Attach the new door lock with the correct cables. Assemble machine back together.
Thats it.
Parts Used:
-
Suryakant from Cortlandt Manor, NY
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
67 of 74 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Washer became unbalanced and broke the latch on door
Had to take the entire front of the washer off to replace the door latch.
Parts Used:
-
Glenn from Las Vegaas, NM
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers
32 of 44 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!