WDF310PAAS4 Whirlpool Dishwasher - Instructions

Removed the old pump, got part number from it, ordered the part. Simply a matter of slipping the new pump into place, reconnecting the electric, testing the machine out to make sure it did not leak. Then slid back in place with the cabinets.

I followed installation instructions from this site and all went well.

Well, it’s very easy to repair. But, what I like if ur Company is, the availability, of the parts.
Thanks you.

As stated above the repair did not go well because the gasket was too wide and the door would close. Suggest you talk with Whirlpool about the part they sold you for my model of dishwasher.

Very simple to repair The front track stops just slide into place, easy. When I looked for these parts this place was the least expensive and the quickest delivery I have ever had. Quick, efficient and friendly online staffing. Thank you, Deb

I just snapped the old one off and snapped the new one on..

based on advice here, concluded the problem was likely that the part "Valve-Inlt" was defective. Our dishwasher intake line is copper and had already developed a partial kink from sometime in the past, so I had to be careful. The final connection to the new part had to happen in place: very close to the floor and underneath, because I didn’t want to stress the copper line. Plus, the shutoff was defective, and it was always leaking while I connected. Awkward. As I was threading on, it started to look like it might be cross-threaded, so I stopped and reversed. Slid the washer back out and disconnected the drain line so I could tip the dishwasher u and inspect. It was going on cross-threaded. Not hard to happen on a metal to a plastic connection. To solve, I carefully made very small bends in the copper inlet line until when it would later be brought up underneath to connect to the inlet valve, it would be as perfectly aligned as possible. This worked. As I tightened, it went a little easier and the leak stopped. A good moment. Tightened a bit more, but didn’t want to overdo it as that can cause other problems. Now the moment of truth: let’s run it. DISHWASHER WORKED AGAIN. Runs fine now and we are glad to have it back. Was satisfying I could do this on my own. The advice and guides here made that possible. Thank you.

New one snapped right into place.

I'm the maintenance supervisor at an apartment complex. While installing a new dishwasher for a tenant, I inadvertently cross-threaded the swivel connector to the fill valve. The valve was ruined and couldn't be repaired. I ordered a new valve (it was an OEM) and installed it. Simple switch out, plus the video from Parts Select showed I had done it right.

Only thing worth saying is that it was a perfect type and fit. Simply lifted the old one out and set the new one in place.
I was pleasantly surprised that it was identical to the old one.

Turned water off. Removed dishwasher from under the counter, replaced hose, reinstalled dishwasher under the counter.

I used a flat blade screwdriver to compress one arm of the endcap of the slide rail to free it. I then slid up the locking slide of the old roller assembly freeing it from the upper basket,and put the new part in its place. I then put the roller back in the slide rail and replaced the endcap.

Pulled out old gasket, pressed in new starting middle top. No more leak.

Followed whirlpool Youtube available for DIY.

Caution....ensure that the pump POWER plug does not loosen when reinserting the pump/drain/filter (middle of dishwasher bottom). The plug can get offset if it hits the electrical conduit or water feed/drain hoses under the dishwasher.

Minimal water when disconnecting drain hoses...have towels at the ready.

Again, follow the Youtube video!

I checked the manual to determine the code meaning for 7 blinks, it was heating issue. I ordered the part from Partselect.com. When the part came in, I googled the internet for "How to replace a dishwasher heating element". There were several options, I chose one that was a video showing a handyman go through each step. I followed the steps, with no problems, and WA-LA! Felt good (as the wife of the house) to do it myself!